Micro Mesh 9 Sanding Sheet Introductory Woodworkers Kit with a 2 inch by 3 inch Foam Sanding Block
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Micro-Mesh is a unique cushioned abrasive that produces a very fine and uniform scratch pattern. The nine grades of abrasives range from 1500 grit to 12000 grit. The 1500 is similar in grit range to conventional 400 grit wet/dry sandpaper. The 12000 will leave a scratch pattern that cannot be detected by the human eye and produces a wonderful looking finish. Micro-Mesh abrasives can polish to a high reflective state or leave a matte or satin finish depending upon where you stop.Before starting the Micro-Mesh cycle of abrasive sanding, coarse sanding should be done using up to 320 grit sandpaper. Shaping, sawing or turning of the work piece should be complete.Begin with 1500 Micro-Mesh. Sand until all of the sandpaper scratches are removed. Continue with the MICRO-MESH series and cycle up to the desired look (1800, 2400, 3200, 3600, 4000, 6000, 8000, 12000). Thinned lemon oil or Danish oil can be applied as a finish on bare wood.MicroMesh performs very well in conjunction with polyurethane, polyester, epoxy, lacquer and so on. Follow the manufacturer’s recommended cure times prior to re-coating or applying the finish coat. When you are applying multiple coats, sand from 1500 Micro-Mesh to 3200 or 3600 between coats to remove any orange-peel or dirt. After the final coat has fully cured, polish the surface beginning with 2400 Micro-Mesh and continue through the series (3200-12000) until the desired gloss is achieved.Satin finishes are achieved by sanding up to the 3600 grade. The satin finish gets progressively higher in gloss through the 6000 step. High gloss finishes will appear by the 6000 through 12000 step. The wood, the finish used and personal preference determine where to stop. Micro-Gloss liquid abrasive can be hand rubbed onto the finish following the 12000 Micro-Mesh step for an “ultra” high gloss finish.?? This Made In the USA KIT INCLUDES: 1 each of the following grit 3 inch by 4 inch sheets: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 and 12000. Also included is a 2 inch by 3 inch foam sanding block. Micro-Mesh can be used wet or dry.
상품설명
Micro-Mesh is a unique cushioned abrasive capable of giving very fine & very controlled scratch patterns. The grits range from 1500 to 12000. The 1500 is slightly more coarse than a conventional 600 grit sandpaper & the 12000 will leave scratch patterns that cannot be detected by the human eye. Micro-Mesh abrasives can polish to an optically clear, reflective state or through the use of a more coarse grit, leave a matte or satin finish. Excellent product to use as a final rub for water-based finishes.
Make sure this fits by entering your model number.Micro-Mesh is a unique cushioned abrasive that produces a very fine and uniform scratch pattern. The nine grades of abrasives range from 1500 grit to 12000 grit. The 1500 is similar in grit range to conventional 400 grit wet/dry sandpaper. The 12000 will leave a scratch pattern that cannot be detected by the human eye and produces a wonderful looking finish. Micro-Mesh abrasives can polish to a high reflective state or leave a matte or satin finish depending upon where you stop.Before starting the Micro-Mesh cycle of abrasive sanding, coarse sanding should be done using up to 320 grit sandpaper. Shaping, sawing or turning of the work piece should be complete.Begin with 1500 Micro-Mesh. Sand until all of the sandpaper scratches are removed. Continue with the MICRO-MESH series and cycle up to the desired look (1800, 2400, 3200, 3600, 4000, 6000, 8000, 12000). Thinned lemon oil or Danish oil can be applied as a finish on bare wood.MicroMesh performs very well in conjunction with polyurethane, polyester, epoxy, lacquer and so on. Follow the manufacturer’s recommended cure times prior to re-coating or applying the finish coat. When you are applying multiple coats, sand from 1500 Micro-Mesh to 3200 or 3600 between coats to remove any orange-peel or dirt. After the final coat has fully cured, polish the surface beginning with 2400 Micro-Mesh and continue through the series (3200-12000) until the desired gloss is achieved.Satin finishes are achieved by sanding up to the 3600 grade. The satin finish gets progressively higher in gloss through the 6000 step. High gloss finishes will appear by the 6000 through 12000 step. The wood, the finish used and personal preference determine where to stop. Micro-Gloss liquid abrasive can be hand rubbed onto the finish following the 12000 Micro-Mesh step for an “ultra” high gloss finish.?? This Made In the USA KIT INCLUDES: 1 each of the following grit 3 inch by 4 inch sheets: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 and 12000. Also included is a 2 inch by 3 inch foam sanding block. Micro-Mesh can be used wet or dry.
상품설명
Micro-Mesh is a unique cushioned abrasive capable of giving very fine & very controlled scratch patterns. The grits range from 1500 to 12000. The 1500 is slightly more coarse than a conventional 600 grit sandpaper & the 12000 will leave scratch patterns that cannot be detected by the human eye. Micro-Mesh abrasives can polish to an optically clear, reflective state or through the use of a more coarse grit, leave a matte or satin finish. Excellent product to use as a final rub for water-based finishes.
2019-03-21 23:19:46
