DRYPRO Waterproof Arm Cast Cover - Sized for both Kids and Adults - Ideal for the Bath Shower or Swimming - Medium Full Arm – (FA-16)
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
IMPORTANT: Ensure correct measurements! Measure the circumference of your arm at two inches above the cast or wound and refer to the size chart for the correct size. Consider both half and full arm sizes. The product will not work if the seal is not snug around the arm.100% airtight & submersible even for swimmingUNIQUE: Vacuum seal technology with proprietary valve & bulb suction designed to cover casts or wounds with a snug waterproof sealSWIMMING, SHOWERING & BATHING: waterproof cast covers that are 100% airtight and submersible even for swimmingREUSABLE: Made in the USA with high quality, durable surgical rubber latex90-DAY MANUFACTURER’S WARRANTY: DRYPRO is Non-Returnable due to the medical nature of the product. However, we ensure a free replacement due to any damages, defects or size exchanges
상품설명
Completely waterproof patented protection for above-the-elbow casts and wounds. Comes with pump to create a vacuum-seal(Please note: color of pumps/bulbs may vary from picture). Once air is removed, drypro can\'t be taken off unintentionally and water can\'t get inside. Bathe, shower or swim without worry of infection or damage to your cast or other arm wound. GUIDELINES: 1) It is IMPORTANT to follow sizing instructions. The vacuum seal will not work unless the opening of the cover fits tightly around the skin above the cast. If the vacuum seal cannot be created and maintained, the product is most likely too big and should not be used in water. 2) If the cover is fitting tightly around the user\'s skin but is too long, simply bunch up the extra material and pump out all the air. The extra latex will shrink down and conform to the shape of the users limb, removing all extra length. 3) If the opening is too tight to slide over the cast, put either a tube sock or panty hose over the cast before you put the cover on. This will allow the cover to slide over the cast more easily. If there is too much discomfort on the arm when using the cast cover, trim the opening of the cover by 1/8th of an inch at a time. This will relieve pressure and create a custom-fitting protector for the user. Non-Skid Grid to Prevent Slipping. Measuring Length: Measure from the tip of the middle finger or heel of the foot to the top end of the cast. It is okay if the cast protector measurement is longer then the limb measurement. The protector will still work. Extra length will be removed when the vacuum seal is created.
IMPORTANT: Ensure correct measurements! Measure the circumference of your arm at two inches above the cast or wound and refer to the size chart for the correct size. Consider both half and full arm sizes. The product will not work if the seal is not snug around the arm.100% airtight & submersible even for swimmingUNIQUE: Vacuum seal technology with proprietary valve & bulb suction designed to cover casts or wounds with a snug waterproof sealSWIMMING, SHOWERING & BATHING: waterproof cast covers that are 100% airtight and submersible even for swimmingREUSABLE: Made in the USA with high quality, durable surgical rubber latex90-DAY MANUFACTURER’S WARRANTY: DRYPRO is Non-Returnable due to the medical nature of the product. However, we ensure a free replacement due to any damages, defects or size exchanges
상품설명
Completely waterproof patented protection for above-the-elbow casts and wounds. Comes with pump to create a vacuum-seal(Please note: color of pumps/bulbs may vary from picture). Once air is removed, drypro can\'t be taken off unintentionally and water can\'t get inside. Bathe, shower or swim without worry of infection or damage to your cast or other arm wound. GUIDELINES: 1) It is IMPORTANT to follow sizing instructions. The vacuum seal will not work unless the opening of the cover fits tightly around the skin above the cast. If the vacuum seal cannot be created and maintained, the product is most likely too big and should not be used in water. 2) If the cover is fitting tightly around the user\'s skin but is too long, simply bunch up the extra material and pump out all the air. The extra latex will shrink down and conform to the shape of the users limb, removing all extra length. 3) If the opening is too tight to slide over the cast, put either a tube sock or panty hose over the cast before you put the cover on. This will allow the cover to slide over the cast more easily. If there is too much discomfort on the arm when using the cast cover, trim the opening of the cover by 1/8th of an inch at a time. This will relieve pressure and create a custom-fitting protector for the user. Non-Skid Grid to Prevent Slipping. Measuring Length: Measure from the tip of the middle finger or heel of the foot to the top end of the cast. It is okay if the cast protector measurement is longer then the limb measurement. The protector will still work. Extra length will be removed when the vacuum seal is created.
2019-06-24 18:05:11
