Lubegard 95030 Engine Flush, 15 oz.
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Use before changing oil in gas or diesel enginesNo harmful solvents to damage seals or gasketsSafely remove accumulated amounts of varnish, sludge and by-products of combustionPremium synthetic blend that contains special detergents and dispersantsPrepares engine for fresh oil
상품설명
Lubegard Engine Flush has better features than traditional oil filters that can typically remove contaminants up to 25 microns, and that's with a great filter. The most dangerous contaminants to your engine are between 5 to 20 microns. These contaminants are larger than the finest tolerances in your engine, but too small for oil filters to remove, causing approximately 60 percent of wear. If these harmful contaminants are not flushed out with a quality flush product - sludge, tar, varnish and wear metals continue to circulate within the engine and accumulate in the passageways, oil pump and oil pan. These contaminants will cause excess wear, higher operating temperatures, and reduced lubrication. After an engine is contaminated, regular oil changes do little to restore its operating efficiency. The detergent and dispersants found in most conventional engine oils can't adequately remove these excessive amounts of contamination. The newly changed oil becomes dirty again within a short period of time, and actually helps to accelerate the formation of even more sludge and varnish. After flushing always use Lubegard bio-tech engine oil protectant (sold separately) with each oil change. It's specifically formulated to reduce engine temperatures and minimize friction and wear. Lubegard's bio-tech engine oil protectant also replenishes oil components that have been lost in the stress of operation. It will save fuel, provide a smoother, quieter and cooler engine and increase engine life. DIRECTIONS FOR USE: With a flush machine - Follow manufacturer’s directions. Without a flush machine - With the engine warm, check for the proper oil level and add new oil if necessary. Add one bottle of LUBEGARD Engine Flush and circulate at idle for 5 to 10 minutes. Stop the engine and drain as usual. Allow sufficient time for the system to drain completely. Install new oil filter and refill with new engine oil in the grade and quality level recommended by the manufacturer. For best protection and additional assurance of top performance and reduction in the formation of further sludge and varnish always use LUBEGARD BIO-TECH Engine Oil Protectant with each oil change. Note: High mileage vehicles and those that have not been maintained properly, according to their service manuals, should have the oil screen and pan examined and cleaned of accumulated dirt and wear materials. Failure to do so can reduce lubricant flow and may lead to engine damage.
Make sure this fits by entering your model number.Use before changing oil in gas or diesel enginesNo harmful solvents to damage seals or gasketsSafely remove accumulated amounts of varnish, sludge and by-products of combustionPremium synthetic blend that contains special detergents and dispersantsPrepares engine for fresh oil
상품설명
Lubegard Engine Flush has better features than traditional oil filters that can typically remove contaminants up to 25 microns, and that's with a great filter. The most dangerous contaminants to your engine are between 5 to 20 microns. These contaminants are larger than the finest tolerances in your engine, but too small for oil filters to remove, causing approximately 60 percent of wear. If these harmful contaminants are not flushed out with a quality flush product - sludge, tar, varnish and wear metals continue to circulate within the engine and accumulate in the passageways, oil pump and oil pan. These contaminants will cause excess wear, higher operating temperatures, and reduced lubrication. After an engine is contaminated, regular oil changes do little to restore its operating efficiency. The detergent and dispersants found in most conventional engine oils can't adequately remove these excessive amounts of contamination. The newly changed oil becomes dirty again within a short period of time, and actually helps to accelerate the formation of even more sludge and varnish. After flushing always use Lubegard bio-tech engine oil protectant (sold separately) with each oil change. It's specifically formulated to reduce engine temperatures and minimize friction and wear. Lubegard's bio-tech engine oil protectant also replenishes oil components that have been lost in the stress of operation. It will save fuel, provide a smoother, quieter and cooler engine and increase engine life. DIRECTIONS FOR USE: With a flush machine - Follow manufacturer’s directions. Without a flush machine - With the engine warm, check for the proper oil level and add new oil if necessary. Add one bottle of LUBEGARD Engine Flush and circulate at idle for 5 to 10 minutes. Stop the engine and drain as usual. Allow sufficient time for the system to drain completely. Install new oil filter and refill with new engine oil in the grade and quality level recommended by the manufacturer. For best protection and additional assurance of top performance and reduction in the formation of further sludge and varnish always use LUBEGARD BIO-TECH Engine Oil Protectant with each oil change. Note: High mileage vehicles and those that have not been maintained properly, according to their service manuals, should have the oil screen and pan examined and cleaned of accumulated dirt and wear materials. Failure to do so can reduce lubricant flow and may lead to engine damage.
2021-01-23 09:04:43
