Speed Painting Tools 88888 1 Pair Door Decker
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.The door decker finishing system is comprised of two steel plates with handles on each attached with brass eyelets. Each plate is securely screwed into the center of either end of a door with a #8 x 1 1/4 inch phillips wafer head screw (included with purchase) prior to paint or stain applicationOne pair used on each door is the best method for the average height/weighted door. Once the door deckers are attached, painting can begin. Spray one side and then with one person on each end of the doors, flip the door and spray the opposite sideThen move the door to an out of the way location for stacking and drying. Continue the process with each additional door. The inter-locking system of the steel plates allows for the door deckers to balance against each other while stacked. This horizontal painting and drying process creates application finishes without runs or sags and stacked up and out of the way for drying - great for saving space on a job siteOnce the paint has dried on the doors, use a knife or sharp edge to score around the edges o the door decker before removing the steel plates. This will ensure that the paint built up between the steel plate and the door itself has been separated and will not risk the tearing of the paint around the edges of the doorWhen painting or staining hollow-core doors, it is recommended stacking the doors for drying only 8-10 doors high. Because the doors are light weight, they are able to be stacked higher, but be aware though that warping can occur if left too long in a horizontal position (see on-edge drying adapters to address this possibility)
상품설명
Speed painting tools 1 Pair Door Decker. The Door Decker Finishing System is comprised of two steel plates with handles on each attached with brass eyelets. Each plate is securely screwed into the center of either end of a door with a #8 x 1 1/4 inch Phillips wafer head screw (included with purchase) prior to paint or stain application. One pair used on each door is the best method for the average height/weighted door. Once the Door Deckers are attached, painting can begin. Spray one side and then with one person on each end of the doors, flip the door and spray the opposite side. Always use a #8 x 1 1/4 inch Phillips wafer head screw when attaching the Door Deckers to the door. Other sizes/types of screws can damage the brass eyelet and weaken the handle over time. Cleaning these tools is a simple process. Toss the Door Deckers into an empty five gallon bucket and soak them in either water or paint thinner, depending on the application type covering the tools. Rinse well and air dry. Provides a system of painting both sides and edges of a door at the same time. The horizontal positioning of the door as it is finished allows the application of a heavier mil thickness without runs or sags. Allows the applicator to finish doors at a comfortable working level without stooping or bending. Saves space by allowing the finished doors to be stacked to dry. Ideal for hollow or solid wood doors, hollow metal doors, shutters and shelves.
Make sure this fits by entering your model number.The door decker finishing system is comprised of two steel plates with handles on each attached with brass eyelets. Each plate is securely screwed into the center of either end of a door with a #8 x 1 1/4 inch phillips wafer head screw (included with purchase) prior to paint or stain applicationOne pair used on each door is the best method for the average height/weighted door. Once the door deckers are attached, painting can begin. Spray one side and then with one person on each end of the doors, flip the door and spray the opposite sideThen move the door to an out of the way location for stacking and drying. Continue the process with each additional door. The inter-locking system of the steel plates allows for the door deckers to balance against each other while stacked. This horizontal painting and drying process creates application finishes without runs or sags and stacked up and out of the way for drying - great for saving space on a job siteOnce the paint has dried on the doors, use a knife or sharp edge to score around the edges o the door decker before removing the steel plates. This will ensure that the paint built up between the steel plate and the door itself has been separated and will not risk the tearing of the paint around the edges of the doorWhen painting or staining hollow-core doors, it is recommended stacking the doors for drying only 8-10 doors high. Because the doors are light weight, they are able to be stacked higher, but be aware though that warping can occur if left too long in a horizontal position (see on-edge drying adapters to address this possibility)
상품설명
Speed painting tools 1 Pair Door Decker. The Door Decker Finishing System is comprised of two steel plates with handles on each attached with brass eyelets. Each plate is securely screwed into the center of either end of a door with a #8 x 1 1/4 inch Phillips wafer head screw (included with purchase) prior to paint or stain application. One pair used on each door is the best method for the average height/weighted door. Once the Door Deckers are attached, painting can begin. Spray one side and then with one person on each end of the doors, flip the door and spray the opposite side. Always use a #8 x 1 1/4 inch Phillips wafer head screw when attaching the Door Deckers to the door. Other sizes/types of screws can damage the brass eyelet and weaken the handle over time. Cleaning these tools is a simple process. Toss the Door Deckers into an empty five gallon bucket and soak them in either water or paint thinner, depending on the application type covering the tools. Rinse well and air dry. Provides a system of painting both sides and edges of a door at the same time. The horizontal positioning of the door as it is finished allows the application of a heavier mil thickness without runs or sags. Allows the applicator to finish doors at a comfortable working level without stooping or bending. Saves space by allowing the finished doors to be stacked to dry. Ideal for hollow or solid wood doors, hollow metal doors, shutters and shelves.
2022-01-27 20:19:19
