HiLetgo Stackable SD Card and TF Card Shield for Arduino UNO R3 Arduino Mega 2560
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.This SD card shield is a standard SD card / TF card break out board for Arduino. The SD card shield adds storage to your Arduino project.Stackable SD Card Shield is a stackable design Arduino SD / TF card expansion board. It supports direct insertion in the Arduino board to extend SD / TF read and write functions.SD / TF card expansion board uses the Arduino hardware ISP interface, so only supports SIP mode SD / TF card.This expansion board uses only a handful of Arduino pins, so the stack design allows you to plug in another expansion board on this board, provided that the same SPI pins are not used, such as Bluetooth expansion board, GPRS expansion board.Many electronic enthusiasts have provided Arduino with a simple documentation program. And we provide a simple TinyFAT file system library, you can easily achieve Arduino control SD / TF card reader - this library only supports FAT16 small capacity card, such as 1G card, if you need to support FAT32, you can use Arduino heard Official library.
상품설명
Features: Compatible SD card, Micro SD card and SDHC card supportable.Prototype expand Library support Size: 53mm x 47mm Weight: 35g Pin With SD Card 5V VCC ---3v3 GND--GND D13---SD_CLK D12-- SD_OUT D11---SD_IN D10--SD_CS 1.The shield is missing pins for SCL and SDA If you need those two for I2C communication like a display shield, you have to use Analog pin 4 and Analog pin 5 2. How to build an eeprom programmer to program 2708s for computer? A: Set the switch to "3.3"and pressed on, SD cards require 3.3v or you could damage them. B:Installed the shield on a Mega 2560 R3 if you need lot of I/O pins forprom programmer,You can plug any shield, in general, into any Arduino as long as you "match" up the pins which are marked. C: Installed the shield on Mega,put the shield on the Duemilanove, changed the chip select pin to "10" again, and Cardinfo ran. Note that when you compile using the IDE, you have to CHANGE the target board to the board you are using or it just won't work. D:when you modify the code, make sure that you replace "10" with "53". 3.You can by googling ""SD shield 3.0"" and clicking on the iTEAD wiki link. A-Put the SD shield on whatever arduino you have. Using the labels on the shield and arduino, make sure the pins match. B-Use the wiki instructions' "Compatibility" section to find out what position the 3.3V/5V selector switch should be in, and whether you need to remove ALL 3 of the adjacent SPI Jumpers on the top of the board given the arduino board you're using. For the arduino DUE,you can remove these jumpers and keep the switch on 3.3V.
Make sure this fits by entering your model number.This SD card shield is a standard SD card / TF card break out board for Arduino. The SD card shield adds storage to your Arduino project.Stackable SD Card Shield is a stackable design Arduino SD / TF card expansion board. It supports direct insertion in the Arduino board to extend SD / TF read and write functions.SD / TF card expansion board uses the Arduino hardware ISP interface, so only supports SIP mode SD / TF card.This expansion board uses only a handful of Arduino pins, so the stack design allows you to plug in another expansion board on this board, provided that the same SPI pins are not used, such as Bluetooth expansion board, GPRS expansion board.Many electronic enthusiasts have provided Arduino with a simple documentation program. And we provide a simple TinyFAT file system library, you can easily achieve Arduino control SD / TF card reader - this library only supports FAT16 small capacity card, such as 1G card, if you need to support FAT32, you can use Arduino heard Official library.
상품설명
Features: Compatible SD card, Micro SD card and SDHC card supportable.Prototype expand Library support Size: 53mm x 47mm Weight: 35g Pin With SD Card 5V VCC ---3v3 GND--GND D13---SD_CLK D12-- SD_OUT D11---SD_IN D10--SD_CS 1.The shield is missing pins for SCL and SDA If you need those two for I2C communication like a display shield, you have to use Analog pin 4 and Analog pin 5 2. How to build an eeprom programmer to program 2708s for computer? A: Set the switch to "3.3"and pressed on, SD cards require 3.3v or you could damage them. B:Installed the shield on a Mega 2560 R3 if you need lot of I/O pins forprom programmer,You can plug any shield, in general, into any Arduino as long as you "match" up the pins which are marked. C: Installed the shield on Mega,put the shield on the Duemilanove, changed the chip select pin to "10" again, and Cardinfo ran. Note that when you compile using the IDE, you have to CHANGE the target board to the board you are using or it just won't work. D:when you modify the code, make sure that you replace "10" with "53". 3.You can by googling ""SD shield 3.0"" and clicking on the iTEAD wiki link. A-Put the SD shield on whatever arduino you have. Using the labels on the shield and arduino, make sure the pins match. B-Use the wiki instructions' "Compatibility" section to find out what position the 3.3V/5V selector switch should be in, and whether you need to remove ALL 3 of the adjacent SPI Jumpers on the top of the board given the arduino board you're using. For the arduino DUE,you can remove these jumpers and keep the switch on 3.3V.
2019-04-02 07:03:26
