6" Mini Power Sluice & Set Up Kit - Gold Mining Equipment
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.6 inch Mini Power Sluice & Set Up Kit includes: 32"L x 6"W sluice AND 8" x 6" x 6" header box AND 8.5" x 24" sluice stand AND flare AND12 volt 800-gph pump AND 4 feet of 3/4" hose. The unique elongated 45 degree z-riffles are great for trapping gold. The riffle cage is also aluminum.Up front ribbed matting for fast gold ID and down below is expanded metal over ribbed miner's carpet. The expanded metal helps keeps the gold in the box and prevents the rocks from knocking it loose.Made in the USA from strong .080 gauge 5052 aircraft aluminum, which is light weight - plus, aluminum makes it easier to use a magnet to remove the black sand build up.Looking for a larger set up? See separate Amazon listing for 10" Mini Power Sluice & Set Up Kit ASIN: B00M2ARUSQ.
상품설명
Size:6" Mini Power Sluice & Set Up Kit This 6 inch Power Sluice Setup Kit includes: 32"L x 6"W sluice AND flare AND 8" x 6" x 6" header box AND 8.5" x 24" sluice stand AND 12 volt 800-gph pump AND 4 feet of 3/4" hose. This power sluice header box setup and the 800-gph 12-volt pump all adds up to a good high volume power sluice! It can also be used with a recovery tub (not included) to complete a power sluice recirculating system. This unit can be used for gold prospecting, sampling, and gold mining. Looking for a larger set up? See separate Amazon listing for 10" Mini Power Sluice & Set Up Kit ASIN: B00M2ARUSQ. Manufacturer's Easy Power Sluice Setup Instructions: 1. Put the legs on the stand so that the front legs are shorter than the back legs. There should be about 4 inches more above the leg bracket than then front. This should provide a 15 degree slope or, one inch per foot of drop. Check the water flow over the riffles and adjust the stand as needed. 2. Unbolt the flare and set it aside. 3. Bolt on the header box in the same place where you took off the flare. 4. Place the sluice with the header box on the stand with the end without the header box under the slot on the stand. There are also side supports on the sluice stand. 5. Place the pump in a bucket and in the stream or in a tub filled with water if using indoors. 6. If using a tub, place it under the discharge end of the sluice so you can recirculate the water. Place bucket with holes around the top in the tub to catch the waste material so it does not get sucked up by the pump. Now you are ready to run your material! Good luck getting the gold!
Make sure this fits by entering your model number.6 inch Mini Power Sluice & Set Up Kit includes: 32"L x 6"W sluice AND 8" x 6" x 6" header box AND 8.5" x 24" sluice stand AND flare AND12 volt 800-gph pump AND 4 feet of 3/4" hose. The unique elongated 45 degree z-riffles are great for trapping gold. The riffle cage is also aluminum.Up front ribbed matting for fast gold ID and down below is expanded metal over ribbed miner's carpet. The expanded metal helps keeps the gold in the box and prevents the rocks from knocking it loose.Made in the USA from strong .080 gauge 5052 aircraft aluminum, which is light weight - plus, aluminum makes it easier to use a magnet to remove the black sand build up.Looking for a larger set up? See separate Amazon listing for 10" Mini Power Sluice & Set Up Kit ASIN: B00M2ARUSQ.
상품설명
Size:6" Mini Power Sluice & Set Up Kit This 6 inch Power Sluice Setup Kit includes: 32"L x 6"W sluice AND flare AND 8" x 6" x 6" header box AND 8.5" x 24" sluice stand AND 12 volt 800-gph pump AND 4 feet of 3/4" hose. This power sluice header box setup and the 800-gph 12-volt pump all adds up to a good high volume power sluice! It can also be used with a recovery tub (not included) to complete a power sluice recirculating system. This unit can be used for gold prospecting, sampling, and gold mining. Looking for a larger set up? See separate Amazon listing for 10" Mini Power Sluice & Set Up Kit ASIN: B00M2ARUSQ. Manufacturer's Easy Power Sluice Setup Instructions: 1. Put the legs on the stand so that the front legs are shorter than the back legs. There should be about 4 inches more above the leg bracket than then front. This should provide a 15 degree slope or, one inch per foot of drop. Check the water flow over the riffles and adjust the stand as needed. 2. Unbolt the flare and set it aside. 3. Bolt on the header box in the same place where you took off the flare. 4. Place the sluice with the header box on the stand with the end without the header box under the slot on the stand. There are also side supports on the sluice stand. 5. Place the pump in a bucket and in the stream or in a tub filled with water if using indoors. 6. If using a tub, place it under the discharge end of the sluice so you can recirculate the water. Place bucket with holes around the top in the tub to catch the waste material so it does not get sucked up by the pump. Now you are ready to run your material! Good luck getting the gold!
2020-11-24 10:15:23
