Pre-Catalyzed Powdered Urea Resin - 5 Pound Pail
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Provides a rigid, theromoset bondWorks particularly well for veneeringCompare to: DAP Weldwood, Unibond 800
상품설명
Application Temperature(s): N/A Color: Light Tan Freeze Thaw Stable: YES Min Use Temperature: 70°F Shelf Life: 12 Months Solids (~): 62% Specific Gravity (~): N/A Viscosity: 1600-2700 Characteristics: Long storage life, long open time, simplified mixing, high water resistance; meets Hardwood Plywood Type II, rigid glue line with no spring back, reduced Bleed through on veneers. Cures from 70° upward. Does not load sandpaper. Applications: Excellent general-purpose wood adhesive for solid wood gluing and veneering. Good for applications requiring unquestioned Type II moisture resistance. Best choice for low/moderate volume veneering and curved millwork. Can be cold pressed, hot pressed and cured by RF. Directions: Storage- Closed container in cool, dry place for one year. Stock- Use freshly machined stock with 6-8% moisture content. Formula and Mixing- Powder 100 parts by weight, Water 50-65 parts by weight, Pour 2/3 water in mixer, Add all powder, mix until lump free (3-5 minutes), Add balance of water, mix until smooth. Spread Rates- Apply enough to provide a thin uniform bead of squeeze-out when under pressure. Veneering: 35-45 lbs/MSGL* Edge gluing: 40-50 lbs/MSGL *MSGL-- thousand square feet single glue Assembly Time- Max. 40 minutes @ 70°F. Depends on temp., moisture content, porosity and spread. Pressing/Clamping- From 75 psi to 200 psi depending on density and stock condition. Press/Clamp time- 4-6 hours @ 70°F; 2-4 hours @ 90°F. Hot pressing- call for technical advice. Allow stock to post cure for 24 hours before machining. Clean Up and Storage: With warm water while glue is wet. Store in cool, dry place in original, sealed container
Make sure this fits by entering your model number.Provides a rigid, theromoset bondWorks particularly well for veneeringCompare to: DAP Weldwood, Unibond 800
상품설명
Application Temperature(s): N/A Color: Light Tan Freeze Thaw Stable: YES Min Use Temperature: 70°F Shelf Life: 12 Months Solids (~): 62% Specific Gravity (~): N/A Viscosity: 1600-2700 Characteristics: Long storage life, long open time, simplified mixing, high water resistance; meets Hardwood Plywood Type II, rigid glue line with no spring back, reduced Bleed through on veneers. Cures from 70° upward. Does not load sandpaper. Applications: Excellent general-purpose wood adhesive for solid wood gluing and veneering. Good for applications requiring unquestioned Type II moisture resistance. Best choice for low/moderate volume veneering and curved millwork. Can be cold pressed, hot pressed and cured by RF. Directions: Storage- Closed container in cool, dry place for one year. Stock- Use freshly machined stock with 6-8% moisture content. Formula and Mixing- Powder 100 parts by weight, Water 50-65 parts by weight, Pour 2/3 water in mixer, Add all powder, mix until lump free (3-5 minutes), Add balance of water, mix until smooth. Spread Rates- Apply enough to provide a thin uniform bead of squeeze-out when under pressure. Veneering: 35-45 lbs/MSGL* Edge gluing: 40-50 lbs/MSGL *MSGL-- thousand square feet single glue Assembly Time- Max. 40 minutes @ 70°F. Depends on temp., moisture content, porosity and spread. Pressing/Clamping- From 75 psi to 200 psi depending on density and stock condition. Press/Clamp time- 4-6 hours @ 70°F; 2-4 hours @ 90°F. Hot pressing- call for technical advice. Allow stock to post cure for 24 hours before machining. Clean Up and Storage: With warm water while glue is wet. Store in cool, dry place in original, sealed container
2019-04-16 05:17:21
