Uniweld FV600 Oxy/Fuel Adapter to Connect an MC Regulator (CGA200) to a Disposable Fuel Cylinder (CGA600)
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Fuel valve adapter to connect Uniweld acetylene MC regulator to a disposable fuel cylinderConnects CGA200 to CGA600Fuel compatibility with other manufactuer's acetylene regulators must be determined prior to usePlastic tote, regulators, tanks, and hose not includedProudly made in the U.S.A
상품설명
Uniweld FV600 oxy/fuel adapter is a fuel valve adapter that is used to connect a Uniweld acetylene MC regulator (CGA200) to a disposable fuel cylinder (CGA600). All Uniweld acetylene regulator diaphragms and seals are capatible for use with either propylene (MAP//Pro) or propane fuel gas. Warning: Fuel compatibility with other manufacturer's acetylene regulators must be determined prior to use. The Uniweld 71 welding handle and Type17 weld/braze tips will work properly using either of the fuel gases combined with oxygen. The CA550 cutting attachment will also work with wither fuel gas. However, the cutting tip is fuel specific and must be changed. Also, Uniweld's Cap'n Hook tips are fuel specific. It is recommended to use grade "T" hose (part# H32AT) with propylene (MAP//Pro) or propane fuel gas. If using grade "R" hose (part# H32A) with propylene (MAP//Pro) or propane fuel gas, it must never be used in extremely cold temperatures below -10 deg F. This may cause the fuel gas to liquefy and act as a solvent that will attack the internal hose material. Always bleed off the remaining fuel gas in the hose after each use. NOTE: There will be a noticeable performance and temperature difference when using propylene (MAP//Pro) versus acetylene and an increase in oxygen consumption. Acetylene burns at 5589 deg F with an oxy/fuel ratio of 1-1 respectively. MAP//Pro burns at 5193 deg F with an oxy/fuel ratio of 3.5 - 1. Propane burns at 4579 deg F with an oxy/fuel ratio of 4 - 1. It is highly recommended to use a Type17-3 or larger tip for brazing 3/8" and 7/8" copper line sets.
Make sure this fits by entering your model number.Fuel valve adapter to connect Uniweld acetylene MC regulator to a disposable fuel cylinderConnects CGA200 to CGA600Fuel compatibility with other manufactuer's acetylene regulators must be determined prior to usePlastic tote, regulators, tanks, and hose not includedProudly made in the U.S.A
상품설명
Uniweld FV600 oxy/fuel adapter is a fuel valve adapter that is used to connect a Uniweld acetylene MC regulator (CGA200) to a disposable fuel cylinder (CGA600). All Uniweld acetylene regulator diaphragms and seals are capatible for use with either propylene (MAP//Pro) or propane fuel gas. Warning: Fuel compatibility with other manufacturer's acetylene regulators must be determined prior to use. The Uniweld 71 welding handle and Type17 weld/braze tips will work properly using either of the fuel gases combined with oxygen. The CA550 cutting attachment will also work with wither fuel gas. However, the cutting tip is fuel specific and must be changed. Also, Uniweld's Cap'n Hook tips are fuel specific. It is recommended to use grade "T" hose (part# H32AT) with propylene (MAP//Pro) or propane fuel gas. If using grade "R" hose (part# H32A) with propylene (MAP//Pro) or propane fuel gas, it must never be used in extremely cold temperatures below -10 deg F. This may cause the fuel gas to liquefy and act as a solvent that will attack the internal hose material. Always bleed off the remaining fuel gas in the hose after each use. NOTE: There will be a noticeable performance and temperature difference when using propylene (MAP//Pro) versus acetylene and an increase in oxygen consumption. Acetylene burns at 5589 deg F with an oxy/fuel ratio of 1-1 respectively. MAP//Pro burns at 5193 deg F with an oxy/fuel ratio of 3.5 - 1. Propane burns at 4579 deg F with an oxy/fuel ratio of 4 - 1. It is highly recommended to use a Type17-3 or larger tip for brazing 3/8" and 7/8" copper line sets.
2019-10-18 09:27:44
