Liberty Supply Professional Maple Tree Tapping Drill Bit for 5/16" Tap Hole
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
5/16" Tapping Bit. Works with all 5/16 taps. Specially engineered 90 degree point.USA MADE! You dont want that black coating in you or your trees.Very effective at removing wood chips. Don\'t blow into the tap hole!Clean cut tap holes stay open longer and produce much more sap!Saves battery life on your drill since it cuts so effeciently. Hex Chuck.
상품설명
These 5/16 bits are designed specifically for tapping Maple Trees. Special 90 degree cut tip is specifically engineered for tap hole drilling. Ask any large producers in the industry and they will tell you the importance of using the correct bit. Hex shaft hold firmly in your drill chuck to keep bit from turning/loosening in your drill. You get a perfectly clean hole with this bit. You DO NOT want to have to blow wood chips out of the hole! You will reduce the amount of sap you will get. This bit blasts the wood chips right out of the hole very efficiently. You DO NOT want an oblong hole! It will leak. You DO NOT want to have to bear down when you drill your hole. This bit pulls itself into the tree so you do not have to push. It saves time, It saves your arms, It gets you more sap, It gives you less leaks and splits, It even makes you drill batteries last longer. Try it side by side with a regular 5/16 bit and you will be amazed by the difference! I was a skeptic until I got my first one years back. Not any more! Little pieces can chip off or rub off into the tree. That is not good for you or the tree. Use the high speed (Usually "2") on your drill when tapping with this bit. Make a wide, stable stance. Hold the bit against the tree before you start to drill. Hold the drill straight and do not push, Let the bit do the work. Keep the bit spinning until you have fully removed it from the tap hole. Most pros tap anywhere from 1.5" to 2" into the tree. Any more than that is probably not good for your tree and also is very unlikely to get you any more sap. Happy Tappin!
5/16" Tapping Bit. Works with all 5/16 taps. Specially engineered 90 degree point.USA MADE! You dont want that black coating in you or your trees.Very effective at removing wood chips. Don\'t blow into the tap hole!Clean cut tap holes stay open longer and produce much more sap!Saves battery life on your drill since it cuts so effeciently. Hex Chuck.
상품설명
These 5/16 bits are designed specifically for tapping Maple Trees. Special 90 degree cut tip is specifically engineered for tap hole drilling. Ask any large producers in the industry and they will tell you the importance of using the correct bit. Hex shaft hold firmly in your drill chuck to keep bit from turning/loosening in your drill. You get a perfectly clean hole with this bit. You DO NOT want to have to blow wood chips out of the hole! You will reduce the amount of sap you will get. This bit blasts the wood chips right out of the hole very efficiently. You DO NOT want an oblong hole! It will leak. You DO NOT want to have to bear down when you drill your hole. This bit pulls itself into the tree so you do not have to push. It saves time, It saves your arms, It gets you more sap, It gives you less leaks and splits, It even makes you drill batteries last longer. Try it side by side with a regular 5/16 bit and you will be amazed by the difference! I was a skeptic until I got my first one years back. Not any more! Little pieces can chip off or rub off into the tree. That is not good for you or the tree. Use the high speed (Usually "2") on your drill when tapping with this bit. Make a wide, stable stance. Hold the bit against the tree before you start to drill. Hold the drill straight and do not push, Let the bit do the work. Keep the bit spinning until you have fully removed it from the tap hole. Most pros tap anywhere from 1.5" to 2" into the tree. Any more than that is probably not good for your tree and also is very unlikely to get you any more sap. Happy Tappin!
2019-03-20 16:18:24
