Walttools Tru Tique (Charcoal Gray) | Concrete Antiquing Wash Color Pigment (19 Colors) - Enhance Textured Surfaces, Similar Look to Powdered Release Without the Mess, Easy to Use
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Water-based antiquing color wash solution designed to provide the natural, two-toned, mottled effect normally obtained by the use of colored release agents. Same effect, but without the mess.This powder is designed to mix with water and be applied as a liquid wash coat. Color will run off the highest spots and settle in the low spots for nice contrast.1500-3000 square feet per bucket based on blend strength.Will work with concrete, overlayment and microtoppings. Very easy to apply.Also the best choice for rejuvenating existing textured surfaces that have faded over time. When all older sealer is removed, you apply according to the instructions, let it dry and you can then reseal the surface with your chosen Walttools sealer product such as Heal and Seal D2k and your surface is as good as new.
상품설명
Color:Charcoal Grey How to use Tru Tique Concrete Antiquing Agent is quite simple: Thoroughly clean the concrete surface before applying Tru Tique. Any existing sealer must be removed if being used on older concrete surfaces. The surface should be free from all sealers, dirt, oil, paint, moss, dust, and other contaminates. Though etching is usually not necessary, bear in mind that the preferred surface is similar to that when applying concrete sealer. We recommend dampening the surface before you apply the Tru Tique especially in hotter weather since since the hot concrete surface will absorb and dry the material quickly. Pour one gallon of clean water into a 5-gallon pail, add 1, 2, or 3 scoops (up to 6 ounces) of Tru Tique powder to the water and mix briskly, making sure all powder is dissolved in the bucket. The more mix you add, the more intense the pigment. Add the mix to a pump sprayer that has a large tip opening and apply evenly over the entire surface. If you do not have a sprayer with an adequate tip you may also use something as simple as a garden watering can. You will need to continuously shake the sprayer to minimize settling of the mixture. A large push broom is often used to help move the product uniformly over the surface. If no broom is available and heavy puddles occur, you can remove the excess with a wet sponge. Once it dries and you see what you have, re-wetting and brushing with a broom can be used to remove material from high spots thereby increasing the contrast of the surface. Once complete allow the Tru Tique wash to dry for 12-24 hours and seal with your favorite Walttools Sealer.
Make sure this fits by entering your model number.Water-based antiquing color wash solution designed to provide the natural, two-toned, mottled effect normally obtained by the use of colored release agents. Same effect, but without the mess.This powder is designed to mix with water and be applied as a liquid wash coat. Color will run off the highest spots and settle in the low spots for nice contrast.1500-3000 square feet per bucket based on blend strength.Will work with concrete, overlayment and microtoppings. Very easy to apply.Also the best choice for rejuvenating existing textured surfaces that have faded over time. When all older sealer is removed, you apply according to the instructions, let it dry and you can then reseal the surface with your chosen Walttools sealer product such as Heal and Seal D2k and your surface is as good as new.
상품설명
Color:Charcoal Grey How to use Tru Tique Concrete Antiquing Agent is quite simple: Thoroughly clean the concrete surface before applying Tru Tique. Any existing sealer must be removed if being used on older concrete surfaces. The surface should be free from all sealers, dirt, oil, paint, moss, dust, and other contaminates. Though etching is usually not necessary, bear in mind that the preferred surface is similar to that when applying concrete sealer. We recommend dampening the surface before you apply the Tru Tique especially in hotter weather since since the hot concrete surface will absorb and dry the material quickly. Pour one gallon of clean water into a 5-gallon pail, add 1, 2, or 3 scoops (up to 6 ounces) of Tru Tique powder to the water and mix briskly, making sure all powder is dissolved in the bucket. The more mix you add, the more intense the pigment. Add the mix to a pump sprayer that has a large tip opening and apply evenly over the entire surface. If you do not have a sprayer with an adequate tip you may also use something as simple as a garden watering can. You will need to continuously shake the sprayer to minimize settling of the mixture. A large push broom is often used to help move the product uniformly over the surface. If no broom is available and heavy puddles occur, you can remove the excess with a wet sponge. Once it dries and you see what you have, re-wetting and brushing with a broom can be used to remove material from high spots thereby increasing the contrast of the surface. Once complete allow the Tru Tique wash to dry for 12-24 hours and seal with your favorite Walttools Sealer.
2019-05-07 21:45:39