FAQ

배대지주소

사이즈조견표
주문/배송조회
입금액충전
입출금내역조회
마일리지조회
입금액환불요청
사업자정보등록
1:1문답
자주하는질문과답 FAQ
국제운송료 요율표
해외물류센터주소
사이즈조견표
취소/반품/교환/환불
파손/분실보상
통관/관세
에스크로서비스
개인정보취급방침
이용약관
회사소개
공지사항
찾아오시는길
아마존배송대행신청방법
아마존 홈               
사진확대

Aluminum Fascia Mount Terminal End Post with 13 Holes (Predrilled) 49 Inch Tall (Cut to Height) for Cable Deck Railing Fence Systems (Powder Coat Black)
ASIN번호 B00USBZ0WY
상품상태 New   
상품구분 Tools & Home Improvement / Building Supplies
브랜드 CableView Railing
판매자 미정
판매자위치 미확인
Color
현지 판매 가격
$84.95
상품가격 상세보기
관련상품



상품특징
Make sure this fits by entering your model number.Comes with a FREE Post Cap Assembly to cover the bottom of your post from insects, debris, etc.!Pre-drilled for your convenience: Will save you sweat, time, and money!Terminal posts have reinforced walls to provide added strength and durabilityCan be cut down with a carbide tipped blade on a cross cut or chopsawPerfect for straight paths and water proof decking, as deck mounting from the top may cause leakage.
상품설명
Color:Black *ALL POSTS ARE OVER SIZED AND MUST BE CUT DOWN ON JOB SITE The foundation of any cable rail system is where the cables begin and end. Our FASCIA MOUNT TERMINAL POST is engineered specifically to withstand the applied stress when each wire rope is tensioned. Each aluminum railing post is manufactured from 6063 T6 aluminum with reinforced walls. Avoid competitor hollow posts that are designed for glass infill. When the cables are tightened in these cable railings, the posts tend to deflect, so the installer must decrease cable tension to reduce the bending. Terminal posts come either pre-drilled with powder-coated holes which eliminates many hours of installation labor, or un-drilled which are used on stairs or ramps. Aluminum posts are designed for through post cable end fittings only. The FASCIA MOUNT TERMINAL POST mounts directly to the rim joist or fascia board by attachment hardware. Usually these are hex bolts (sold separately). SPECIFICATIONS Available for either 36" or 42" rail heights. 2-3/8" by 2-3/8" square • 13 9mm predrilled holes (requiring 13 cable runs), for a total railing height of 42" above deck boards. • 11 9mm predrilled holes (requiring 11 cable runs), for a total railing height of 36" above deck boards. • Qty (2) mounting holes must be drilled. • Can be cut down with a carbide tipped blade on a chop saw Aluminum systems are NOT recommended near salt water, check out our 316 Marine Grade Stainless Steel Systems, as they are more corrosion resistant. Verify with local building codes.
































상품특징
Make sure this fits by entering your model number.Comes with a FREE Post Cap Assembly to cover the bottom of your post from insects, debris, etc.!Pre-drilled for your convenience: Will save you sweat, time, and money!Terminal posts have reinforced walls to provide added strength and durabilityCan be cut down with a carbide tipped blade on a cross cut or chopsawPerfect for straight paths and water proof decking, as deck mounting from the top may cause leakage.
상품설명
Color:Black *ALL POSTS ARE OVER SIZED AND MUST BE CUT DOWN ON JOB SITE The foundation of any cable rail system is where the cables begin and end. Our FASCIA MOUNT TERMINAL POST is engineered specifically to withstand the applied stress when each wire rope is tensioned. Each aluminum railing post is manufactured from 6063 T6 aluminum with reinforced walls. Avoid competitor hollow posts that are designed for glass infill. When the cables are tightened in these cable railings, the posts tend to deflect, so the installer must decrease cable tension to reduce the bending. Terminal posts come either pre-drilled with powder-coated holes which eliminates many hours of installation labor, or un-drilled which are used on stairs or ramps. Aluminum posts are designed for through post cable end fittings only. The FASCIA MOUNT TERMINAL POST mounts directly to the rim joist or fascia board by attachment hardware. Usually these are hex bolts (sold separately). SPECIFICATIONS Available for either 36" or 42" rail heights. 2-3/8" by 2-3/8" square • 13 9mm predrilled holes (requiring 13 cable runs), for a total railing height of 42" above deck boards. • 11 9mm predrilled holes (requiring 11 cable runs), for a total railing height of 36" above deck boards. • Qty (2) mounting holes must be drilled. • Can be cut down with a carbide tipped blade on a chop saw Aluminum systems are NOT recommended near salt water, check out our 316 Marine Grade Stainless Steel Systems, as they are more corrosion resistant. Verify with local building codes.




























2019-05-29 14:05:12