BMW E46 2000-2004 320i M54 2.2L & 2.5L DISA VALVE UNIT FLAP PLATE REPAIR KIT X8R43
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Our repair kit in this listing addresses the common failure of the BMW DISA 2.0 ltr intake adjuster valve unit. Our components described herein with the assistance of our supportive instruction media will allow you to replace the faulty components which always fail within the DISA unit, without having to replace it with another OEM part that is going to fail again due to the same manufacture faults. An extremely common fault corrected by our repair kit.Symptoms of fault: The symptoms of this fault are very obvious; there is a rattling noise coming from the DISA valve, SES light is lit and getting a lean mixture fault or rough running at idle. Fault codes: lean condition(P1083, P1085), front oxygen sensor lean (P1090, P1092) oxygen sensor slow response (P1087, P1089) and cylinder misfire (P0311-P0316) fuel control mixture lean (bank 2 sensor 1) and p0174 system too lean, showing?The solution: Fit our improved design billet aluminium flap kit, designed to never fail, save the cost of a replacement DISA valve which will only fail again. Using our kit the weak components of the DISA valve the flap and crank lever are replaced with our many times stronger billet aluminium parts, retained by our precision machined screw which tightly retains the two components together; eliminating wear and the need for the retaining pin which can enter the engine.You will receive: Our repair kit includes all the components you will need to restore your BMW DISA unit, you will recieve the components shown above.Instructions:1) https://youtu.be/kIq7QJpRnRw 2) https://www.x8r.co.uk/ebay_x8r/instructionspdf/Bmw-DISA-Valve-Unit-Rattle-Repair-Fix-Kit-Rattling.pdf
상품설명
The cause: The original plastic Disa valve components wear and often snap causing the symptoms noted above. The pin retaining the flap can also pop out entering the engine! The likely cause of the faults noted above and most common cause is the weak plastic components within the DISA valve unit vibrating together and wearing causing the flap to operate at the wrong times and eventually leading to destruction of the flap plate. The pieces of this flap can even enter the engine often causing severe engine damage; likewise the metal pin that holds the flap plate in position can vibrate loose and enter the engine. The solution: Fit our improved design billet aluminium flap kit, designed to never fail, save the cost of a replacement DISA valve which will only fail again. Using our kit the weak components of the DISA valve the flap and crank lever are replaced with our many times stronger billet aluminium parts, retained by our precision machined screw which tightly retains the two components together; eliminating wear and the need for the retaining pin which can enter the engine. Our part is completely redesigned to never fail- OEM clearances are reduced minimising vibrations in the part preventing any future failure. Our kit also includes a high temperature Viton 75 O-ring to make a good seal between the DISA unit and the manifold eliminating any air leaks. Vehicles Affected: BMW M54 2.2 &2.5 Liter Applications E36 2000-2002 Z3 2.5i Roadster E39 2000-2003 525i Touring E39 2000-2003 525i Sedan E46 2000-2004 320i Sedan E46 2000-2006 325Ci Coupe+M56 E46 2000-2006 325Ci Convertible E46 2000-2005 325i Touring E46 2000-2005 325i Sedan E46 1999-2004 325xi Sedan E46 1999-2005 325xi Touring E60 2002-2004 525i Sedan E83 2003-2006 X3 2.5i SUV E85 2002-2005 Z4 2.5i Roadster BMW Part# : 11617544806 or 11617502269 Number Stamped on DISA Housing: 7544806 or 7502269
Make sure this fits by entering your model number.Our repair kit in this listing addresses the common failure of the BMW DISA 2.0 ltr intake adjuster valve unit. Our components described herein with the assistance of our supportive instruction media will allow you to replace the faulty components which always fail within the DISA unit, without having to replace it with another OEM part that is going to fail again due to the same manufacture faults. An extremely common fault corrected by our repair kit.Symptoms of fault: The symptoms of this fault are very obvious; there is a rattling noise coming from the DISA valve, SES light is lit and getting a lean mixture fault or rough running at idle. Fault codes: lean condition(P1083, P1085), front oxygen sensor lean (P1090, P1092) oxygen sensor slow response (P1087, P1089) and cylinder misfire (P0311-P0316) fuel control mixture lean (bank 2 sensor 1) and p0174 system too lean, showing?The solution: Fit our improved design billet aluminium flap kit, designed to never fail, save the cost of a replacement DISA valve which will only fail again. Using our kit the weak components of the DISA valve the flap and crank lever are replaced with our many times stronger billet aluminium parts, retained by our precision machined screw which tightly retains the two components together; eliminating wear and the need for the retaining pin which can enter the engine.You will receive: Our repair kit includes all the components you will need to restore your BMW DISA unit, you will recieve the components shown above.Instructions:1) https://youtu.be/kIq7QJpRnRw 2) https://www.x8r.co.uk/ebay_x8r/instructionspdf/Bmw-DISA-Valve-Unit-Rattle-Repair-Fix-Kit-Rattling.pdf
상품설명
The cause: The original plastic Disa valve components wear and often snap causing the symptoms noted above. The pin retaining the flap can also pop out entering the engine! The likely cause of the faults noted above and most common cause is the weak plastic components within the DISA valve unit vibrating together and wearing causing the flap to operate at the wrong times and eventually leading to destruction of the flap plate. The pieces of this flap can even enter the engine often causing severe engine damage; likewise the metal pin that holds the flap plate in position can vibrate loose and enter the engine. The solution: Fit our improved design billet aluminium flap kit, designed to never fail, save the cost of a replacement DISA valve which will only fail again. Using our kit the weak components of the DISA valve the flap and crank lever are replaced with our many times stronger billet aluminium parts, retained by our precision machined screw which tightly retains the two components together; eliminating wear and the need for the retaining pin which can enter the engine. Our part is completely redesigned to never fail- OEM clearances are reduced minimising vibrations in the part preventing any future failure. Our kit also includes a high temperature Viton 75 O-ring to make a good seal between the DISA unit and the manifold eliminating any air leaks. Vehicles Affected: BMW M54 2.2 &2.5 Liter Applications E36 2000-2002 Z3 2.5i Roadster E39 2000-2003 525i Touring E39 2000-2003 525i Sedan E46 2000-2004 320i Sedan E46 2000-2006 325Ci Coupe+M56 E46 2000-2006 325Ci Convertible E46 2000-2005 325i Touring E46 2000-2005 325i Sedan E46 1999-2004 325xi Sedan E46 1999-2005 325xi Touring E60 2002-2004 525i Sedan E83 2003-2006 X3 2.5i SUV E85 2002-2005 Z4 2.5i Roadster BMW Part# : 11617544806 or 11617502269 Number Stamped on DISA Housing: 7544806 or 7502269
2019-11-21 18:56:33
