Jewelry laser welding machine Spot Welder Gold Silver with Handle tool 110V 400W
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Power supply: 110V 60HzPower: 400WAmpere for welding: 0.5 ~ 50A, continuous adjustable (fluctuation)Weight: about 6kgSize: 340 * 320 * 320mm
상품설명
Steps: 1. Plug the device into the wall socket and turn it on 2. Adjust input current by adjusting the current regulating dial to 1-1.5 to start. The current regulating dial ranges from 1-8. The dial can be adjusted as necessary depending upon the current flow that gives best results for your target material. 3. Check that gas is flowing over the tungsten tip with your finger. Adjust Argon gas until you can just feel the flow. 4. Clamp the object to be welded with the negative ground electrode. You cannot short circuit the machine by having both the tungsten needle and the ground clamp in contact through the work piece at the same time. Do not have the target work piece in direct contact with the tungsten needle. A 0.5mm arc gap is necessary for pulse welder operation. This is the optimum distance for welding. 5. Insure you have arc welding eye protection in place. The arc emits short wave UV radiation that will cause eye retinal burns and skin burns. Cover exposed skin (a shirt is fine), wear gloves and use an arc welding helmet. 6. Briefly step on the foot pedal and release. The arc will have pulsed and spot welded at the point you had the tungsten electrode. Attention: Do not step on the pedal with long time, just step it 1 time then move off immediately. Long time stepping on the pedal, machine will be short circuit, even to burn out inside electricity This machine is precision equipment, please cherish it. Spark light during the welding is harmful to eyes, please make sure good protection measures. When you step pedal, do not touch needle or soldering metal. Please do not disassemble the unit without professional guidance. Package Included: 1x Welder, 1x Foot Pedal 1x Cable 1x Forceps Clamp 1x Tungsten Needle 1 x handle welder
Make sure this fits by entering your model number.Power supply: 110V 60HzPower: 400WAmpere for welding: 0.5 ~ 50A, continuous adjustable (fluctuation)Weight: about 6kgSize: 340 * 320 * 320mm
상품설명
Steps: 1. Plug the device into the wall socket and turn it on 2. Adjust input current by adjusting the current regulating dial to 1-1.5 to start. The current regulating dial ranges from 1-8. The dial can be adjusted as necessary depending upon the current flow that gives best results for your target material. 3. Check that gas is flowing over the tungsten tip with your finger. Adjust Argon gas until you can just feel the flow. 4. Clamp the object to be welded with the negative ground electrode. You cannot short circuit the machine by having both the tungsten needle and the ground clamp in contact through the work piece at the same time. Do not have the target work piece in direct contact with the tungsten needle. A 0.5mm arc gap is necessary for pulse welder operation. This is the optimum distance for welding. 5. Insure you have arc welding eye protection in place. The arc emits short wave UV radiation that will cause eye retinal burns and skin burns. Cover exposed skin (a shirt is fine), wear gloves and use an arc welding helmet. 6. Briefly step on the foot pedal and release. The arc will have pulsed and spot welded at the point you had the tungsten electrode. Attention: Do not step on the pedal with long time, just step it 1 time then move off immediately. Long time stepping on the pedal, machine will be short circuit, even to burn out inside electricity This machine is precision equipment, please cherish it. Spark light during the welding is harmful to eyes, please make sure good protection measures. When you step pedal, do not touch needle or soldering metal. Please do not disassemble the unit without professional guidance. Package Included: 1x Welder, 1x Foot Pedal 1x Cable 1x Forceps Clamp 1x Tungsten Needle 1 x handle welder
2020-04-27 23:37:57
