Best Value Vacs 5.5" x 7" Vacuum Chamber Digital Heat Pad
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Chamber NOT Included, Sold Separately. Heat Pad must fit correct size of the chamber! Fits a 2.75 Rectangle ChamberUL Listed Fahrenheit Digital Controller.Min Temp: Ambient + 5Max Temp: 160F, Voltage: 110VAC Only, Power Consumption: 100-wattDigital Control: Increments of 1 Degree, Accuracy: +/- 0.2 Degrees, Units: Degrees FahrenheitInstructions: Fully included, Relay Lifespan: Approx. 10 million cycles, User can reprogram: Yes
상품설명
This Fahrenheit Heat Pad will adhere to the bottom of the chamber with a peel and stick backing, It will come with simple standoff bumpers that will provide thermal separation from the work surface. The bumpers do not stick well to silicone but get the job done. This heater is super accurate, and will hold a temp within a degree (depending on the environment and air movement)The heater includes full instructions to operate it and make PID controller changes. You can leave this heater on for months without any off time.The pad comes with thermal tape seen in the images above. This will be used with a thermal laser gun to shoot the temps. If you have a thermocouple that would be the best method to check and verify temps. The controller has a temperature offset that will need to be found to set the controller accurately. Anything you attach a heat pad to will act like a heat sink. So the set temperature will be different from the actual inside temperature. However, our instructions tell you and provide the thermal labels to accurately find the offset and program the difference in. For example: If you set the 3 gallon shatter vac chamber in the image above to 110F the actual temp on the bottom surface inside the chamber will read about 101F on the thermal label. (don't move the gun around, thermal labels reflect lasers too) Since the inside is reading 101F and the controller is set to 110F your offset is 9F, soAdd 9 Degrees to the 110F setting (119F) and you will achieve your 110F on the inside surface of the chamber. *Signature Required Upon Delivery*
Make sure this fits by entering your model number.Chamber NOT Included, Sold Separately. Heat Pad must fit correct size of the chamber! Fits a 2.75 Rectangle ChamberUL Listed Fahrenheit Digital Controller.Min Temp: Ambient + 5Max Temp: 160F, Voltage: 110VAC Only, Power Consumption: 100-wattDigital Control: Increments of 1 Degree, Accuracy: +/- 0.2 Degrees, Units: Degrees FahrenheitInstructions: Fully included, Relay Lifespan: Approx. 10 million cycles, User can reprogram: Yes
상품설명
This Fahrenheit Heat Pad will adhere to the bottom of the chamber with a peel and stick backing, It will come with simple standoff bumpers that will provide thermal separation from the work surface. The bumpers do not stick well to silicone but get the job done. This heater is super accurate, and will hold a temp within a degree (depending on the environment and air movement)The heater includes full instructions to operate it and make PID controller changes. You can leave this heater on for months without any off time.The pad comes with thermal tape seen in the images above. This will be used with a thermal laser gun to shoot the temps. If you have a thermocouple that would be the best method to check and verify temps. The controller has a temperature offset that will need to be found to set the controller accurately. Anything you attach a heat pad to will act like a heat sink. So the set temperature will be different from the actual inside temperature. However, our instructions tell you and provide the thermal labels to accurately find the offset and program the difference in. For example: If you set the 3 gallon shatter vac chamber in the image above to 110F the actual temp on the bottom surface inside the chamber will read about 101F on the thermal label. (don't move the gun around, thermal labels reflect lasers too) Since the inside is reading 101F and the controller is set to 110F your offset is 9F, soAdd 9 Degrees to the 110F setting (119F) and you will achieve your 110F on the inside surface of the chamber. *Signature Required Upon Delivery*
2019-03-29 15:16:33
