HMK S234 Stone Impregnating Sealer for Granite, Marble & All Stone.
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.IMPREGNATING SEALER FOR MARBLE AND GRANITE - and all Natural Stone SurfacesSILICONE BASED PENETRATING STONE SEALER - Solvent based impregnator penetrates deeper into stone than water based productsINVISIBLE SEALER - Will not alter the natural appearance of your stoneSUPERIOR PROTECTION FROM STAINS - Industrial Grade Stone Sealer that you can apply yourselfSEALER TO PROTECT AGAINST OIL AND GREASE STAINS - Protect your Granite & Marble from Grease Splatter and Food Spills
상품설명
NOTE: THIS ITEM MUST BE SHIPPED VIA UPS GROUND - NO AIR SHIPMENTS ALLOWED HMK S234 is a special impregnator for all natural and artificial stone, agglomerates and terrazzo. S234 reduces the penetration of water, dirt, oil and grease on all finishes, including polished surfaces. Surfaces treated with S234 remain vapor permeable and will have little to no aesthetic enhancement. Important: Clean surface thoroughly before treatment using HMK R155 Intensive Cleaner (diluted) followed by a flood rinse with water and allow at least 24 hours to dry (max residual moisture of 2-4%) before sealing. If under floor heating exists, switch it off and allow the surface to cool to room temperature. Instructions: Apply HMK S234 generously and evenly to a chemically clean and dry surface with a natural bristle paint brush or the HMK Z950-HMK Z951 brushes. Two saturating, wet-on-wet applications are usually sufficient depending on porosity of the stone. Thoroughly remove excess product before drying on the surface. For more absorbent surfaces additional applications may be required. Subsequent applications may be done within fifteen minutes of the initial application, but it is best to wait 24 hours between applications to best determine saturation level. Smears or imperfections left after the application process can be removed using a soft clean cloth moistened with S234 or pure mineral spirits and buffing. Do not walk on the treated surface until 2-4 hours after treatment is completed. Resistance to oil and water is developed over 48 hours. Protect surface from rain and humidity for 12 hours. Do not apply to rubber, plastics, lacquered or varnished surfaces and solvent intolerant materials. Remove all foodstuffs from the area to be treated before work is commenced. Once dry the residual material is not harmful to health. For regular cleaning and continued protection use HMK P324 Liquid Stone Soap. Coverage: About 50 to 220 square feet per liter.
Make sure this fits by entering your model number.IMPREGNATING SEALER FOR MARBLE AND GRANITE - and all Natural Stone SurfacesSILICONE BASED PENETRATING STONE SEALER - Solvent based impregnator penetrates deeper into stone than water based productsINVISIBLE SEALER - Will not alter the natural appearance of your stoneSUPERIOR PROTECTION FROM STAINS - Industrial Grade Stone Sealer that you can apply yourselfSEALER TO PROTECT AGAINST OIL AND GREASE STAINS - Protect your Granite & Marble from Grease Splatter and Food Spills
상품설명
NOTE: THIS ITEM MUST BE SHIPPED VIA UPS GROUND - NO AIR SHIPMENTS ALLOWED HMK S234 is a special impregnator for all natural and artificial stone, agglomerates and terrazzo. S234 reduces the penetration of water, dirt, oil and grease on all finishes, including polished surfaces. Surfaces treated with S234 remain vapor permeable and will have little to no aesthetic enhancement. Important: Clean surface thoroughly before treatment using HMK R155 Intensive Cleaner (diluted) followed by a flood rinse with water and allow at least 24 hours to dry (max residual moisture of 2-4%) before sealing. If under floor heating exists, switch it off and allow the surface to cool to room temperature. Instructions: Apply HMK S234 generously and evenly to a chemically clean and dry surface with a natural bristle paint brush or the HMK Z950-HMK Z951 brushes. Two saturating, wet-on-wet applications are usually sufficient depending on porosity of the stone. Thoroughly remove excess product before drying on the surface. For more absorbent surfaces additional applications may be required. Subsequent applications may be done within fifteen minutes of the initial application, but it is best to wait 24 hours between applications to best determine saturation level. Smears or imperfections left after the application process can be removed using a soft clean cloth moistened with S234 or pure mineral spirits and buffing. Do not walk on the treated surface until 2-4 hours after treatment is completed. Resistance to oil and water is developed over 48 hours. Protect surface from rain and humidity for 12 hours. Do not apply to rubber, plastics, lacquered or varnished surfaces and solvent intolerant materials. Remove all foodstuffs from the area to be treated before work is commenced. Once dry the residual material is not harmful to health. For regular cleaning and continued protection use HMK P324 Liquid Stone Soap. Coverage: About 50 to 220 square feet per liter.
2019-03-25 20:49:44