Anmbest 5PCS L298N Dual H Bridge DC Stepper Motor Driver Controller Board Module for Arduino Smart Car UNO R3 Raspberry Pi Mega2560
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.HIGH EFFICIENCY: Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.Wide Drive Voltage, High Drive Current: The module can drive DC motors that have voltages between 5 and 35V, with a peak current up to 2A.HIGH RELIABILITY: Large capacity filter capacitance, afterflow protection diode, more stable and reliable.INTUITIVE: Control direction indicator, power indicator, current detection, logical part of the plate to take power interface.ATTENTION: This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
상품설명
Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage,high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals.The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con-nection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage. Technical Specifications: Driver: L298N Operating mode: H-bridge driver (dual) Driver power supply: +5V/DC to +35V/DC Drive current: 2A (MAX single bridge) Logic power output Vss: +5/DC to 7V/DC (internal supply +5V/DC) Logic current: 0 - 36mA Controlling level: Low -0.3V/DC to 1.5V/DC, high: 2.3V/DC to Vss Enable signal level: Low -0.3V/DC to 1.5V/DC, high: 2.3V/DC - Vss Max power: 25W Working temperature: -25℃ to +130℃ Storage Temperature: -20 ℃ to ℃ to +135 Size: 43x43x27mm Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply, DO NOT input voltage to +5v supply interface. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 Package includes: 1 x L298N Motor Drive Board Module
Make sure this fits by entering your model number.HIGH EFFICIENCY: Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.Wide Drive Voltage, High Drive Current: The module can drive DC motors that have voltages between 5 and 35V, with a peak current up to 2A.HIGH RELIABILITY: Large capacity filter capacitance, afterflow protection diode, more stable and reliable.INTUITIVE: Control direction indicator, power indicator, current detection, logical part of the plate to take power interface.ATTENTION: This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
상품설명
Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage,high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals.The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con-nection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage. Technical Specifications: Driver: L298N Operating mode: H-bridge driver (dual) Driver power supply: +5V/DC to +35V/DC Drive current: 2A (MAX single bridge) Logic power output Vss: +5/DC to 7V/DC (internal supply +5V/DC) Logic current: 0 - 36mA Controlling level: Low -0.3V/DC to 1.5V/DC, high: 2.3V/DC to Vss Enable signal level: Low -0.3V/DC to 1.5V/DC, high: 2.3V/DC - Vss Max power: 25W Working temperature: -25℃ to +130℃ Storage Temperature: -20 ℃ to ℃ to +135 Size: 43x43x27mm Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply, DO NOT input voltage to +5v supply interface. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 Package includes: 1 x L298N Motor Drive Board Module
2019-05-28 14:55:49
