Hendlex Car Paint Coating Ceramic Coat FS60 | Nano 9H Hydrophobic Coating for Car Body Paint Protection (6.76oz)
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.PROTECTION FROM SCRATCHES | Enhances the hardness of the surface by creating additional protection against minor scratches.HYDROPHOBIC PROPERTIES | Provides the surface with very strong hydrophobic properties and with the “easy cleaning effect”. The angle of a contact with water is more than 100 degrees therefore the surface remains clean for much longer period of time.CAR PAINT SHINE | Significantly highlights the color of paint and provides it with greater shine. Does not attract dust.ANTI DUST, ANTI RUST | Protects the surface from environmental impacts, resistant to pH2-pH12, road salts and UV rays. It also protects the surface from aging and provides it with additional protection from corrosion.FULL KIT READY TO USE | The box contains: Nano ceramic shield Hendlex CERAMIC COAT FS60 (40 ml); Microfibre Cloth x2 Aplication cloths x1 Coating aplicator Protective gloves x2 Instruction
상품설명
Size:6.76oz USERS MANUAL: Preparation of surface. If car is waxed, remove wax using HENDLEX Wax Remover. Wash the car carefully. Make sure there is no washing products (shampoo, dirt solvent) left on the surface. It is recommended to coat polished surface of a car if you want to get a better result. If you have polished the car, make sure to wash it again. Make sure there is no water left in the spaces between the car parts. It is recommended to remove the remaining water using the compressed air jet. It is also recommended to remove dirt and fat using HENDLEX Pain Prepair. Coating of surface. Do not apply the coating in direct sunlight. Proper temperature for coating is from 5 °C to 25 °C. While coating, use the nitrile gloves that are in the set. Hold the applicator by the solid part. Put the application cloth onto the soft part of the applicator (nonwoven fiber cloth). Open the bottle and wet the application cloth in different spots. Cover the surface evenly; make sure that you did not leave uncovered spots. It is recommended to cover the area of 1x1 m at the time. If the temperature is higher than 25 °C, cover the smaller area. The surface must be polished in 60 seconds after coverage. If the surface gets into contact with water, immediately clean it and repeat the coating. Continue coating areas up to 1x1 m until the full surface of the car is covered. After covering each area, polish it again with micro fiber cloth and make sure there are no unpolished spot left. If there is an unpolished spot and it does not get polished with any effort, use paint polishing paste. Cleaned area must be covered again. ATTENTION! It is recommended to keep the surface in higher than 18 °C temperature for 24 hours and prevent it from getting into contact with water. Depending on the temperature of the environment, the coating fully hardens in 48-72 hours. Covered area: 40 ml - 8 m2.
Make sure this fits by entering your model number.PROTECTION FROM SCRATCHES | Enhances the hardness of the surface by creating additional protection against minor scratches.HYDROPHOBIC PROPERTIES | Provides the surface with very strong hydrophobic properties and with the “easy cleaning effect”. The angle of a contact with water is more than 100 degrees therefore the surface remains clean for much longer period of time.CAR PAINT SHINE | Significantly highlights the color of paint and provides it with greater shine. Does not attract dust.ANTI DUST, ANTI RUST | Protects the surface from environmental impacts, resistant to pH2-pH12, road salts and UV rays. It also protects the surface from aging and provides it with additional protection from corrosion.FULL KIT READY TO USE | The box contains: Nano ceramic shield Hendlex CERAMIC COAT FS60 (40 ml); Microfibre Cloth x2 Aplication cloths x1 Coating aplicator Protective gloves x2 Instruction
상품설명
Size:6.76oz USERS MANUAL: Preparation of surface. If car is waxed, remove wax using HENDLEX Wax Remover. Wash the car carefully. Make sure there is no washing products (shampoo, dirt solvent) left on the surface. It is recommended to coat polished surface of a car if you want to get a better result. If you have polished the car, make sure to wash it again. Make sure there is no water left in the spaces between the car parts. It is recommended to remove the remaining water using the compressed air jet. It is also recommended to remove dirt and fat using HENDLEX Pain Prepair. Coating of surface. Do not apply the coating in direct sunlight. Proper temperature for coating is from 5 °C to 25 °C. While coating, use the nitrile gloves that are in the set. Hold the applicator by the solid part. Put the application cloth onto the soft part of the applicator (nonwoven fiber cloth). Open the bottle and wet the application cloth in different spots. Cover the surface evenly; make sure that you did not leave uncovered spots. It is recommended to cover the area of 1x1 m at the time. If the temperature is higher than 25 °C, cover the smaller area. The surface must be polished in 60 seconds after coverage. If the surface gets into contact with water, immediately clean it and repeat the coating. Continue coating areas up to 1x1 m until the full surface of the car is covered. After covering each area, polish it again with micro fiber cloth and make sure there are no unpolished spot left. If there is an unpolished spot and it does not get polished with any effort, use paint polishing paste. Cleaned area must be covered again. ATTENTION! It is recommended to keep the surface in higher than 18 °C temperature for 24 hours and prevent it from getting into contact with water. Depending on the temperature of the environment, the coating fully hardens in 48-72 hours. Covered area: 40 ml - 8 m2.
2020-08-01 21:16:01