Gizmo Dorks PEI Sheet 3D Printer Build Surface 235mm x 235mm (9.3" x 9.3") with Preapplied Laminated 3M 468MP Adhesive for Creality Ender 3 or CR 20 | Made in The USA
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Made in the USA - Ultem 1000 PEI sheet installs quickly via the laminated adhesive on top of existing flat build platforms (e.g. borosilicate glass)Bubble free application - The 3M 468MP adhesive is already preapplied to the PEI; simply peel back the tape liner for quick adhesion to the bedBuild Surface - PEI is the perfect no prep build surface which is endlessly reusable for multiple prints; clean with isopropypl alcohol between prints (or with acetone on a COLD bed)ABS and PLA filaments (along with many other materials) print directly on to PEI surface without the need for additional adhesives, tapes, or slurryDimensions: 235 x 235mm / PEI thickness: 0.56mm (0.022 inches) / Laminated 3M 468MP adhesive thickness: 0.13mm (0.005 inches) / Fits the Creality Ender 3 or Creality CR 20 perfectly!
상품설명
InstallationThe polyetherimide sheet comes with 3M 468MP adhesive already laminated to the PEI. Apply the PEI with slight pressure and at an angle to prevent and minimize air bubbles. Once applied set the print bed to 60C and apply pressure evenly across the PEI in a sweeping fashion to firmly set the adhesive. Please use a towel to avoid getting burned. Level the bed and set the height of the nozzle before printing.If PEI is installed to the top surface of a bed sandwich (a build plate with multiple layers), it is recommended to install PEI on top of borosilicate glass.UseHeat the bed to the desired temperatures for printing (60 C for PLA and 100 C for ABS). Depending on how thick your bed sandwich is, your set temperature may not be your surface PEI temperature.When the print is completed, let the bed cool, and the part will be easy to release from the PEI surface. Parts are easier to remove if released before the bed becomes completely cold.Leveling the bed is very, very important when using PEI. You want the first layer to be close enough to be squished a little. PETG is an exception and doesn't like squished layers, in which case a Z gap should be used.MaintenanceClean in between prints with isopropyl alcohol. Acetone can be used instead of isopropyl alcohol, but the bed must be cold if acetone is used. Optionally, light sanding with 600-1000 grit sand paper can be done after lots of printing to give the PEI sheet more life.CompatibilityCreality Ender 3 / Creality CR 20 / and more!The Creality Ender 3 and the CR 20 have build volumes of 220 x 220mm with a plate size of 235 x 235mm.Dimensions235mm x 235mm (9.25 x 9.25 inches) PEI thickness: 0.56mm (0.022 inches) 3M 468MP adhesive thickness: 0.13mm (0.005 inches)
Make sure this fits by entering your model number.Made in the USA - Ultem 1000 PEI sheet installs quickly via the laminated adhesive on top of existing flat build platforms (e.g. borosilicate glass)Bubble free application - The 3M 468MP adhesive is already preapplied to the PEI; simply peel back the tape liner for quick adhesion to the bedBuild Surface - PEI is the perfect no prep build surface which is endlessly reusable for multiple prints; clean with isopropypl alcohol between prints (or with acetone on a COLD bed)ABS and PLA filaments (along with many other materials) print directly on to PEI surface without the need for additional adhesives, tapes, or slurryDimensions: 235 x 235mm / PEI thickness: 0.56mm (0.022 inches) / Laminated 3M 468MP adhesive thickness: 0.13mm (0.005 inches) / Fits the Creality Ender 3 or Creality CR 20 perfectly!
상품설명
InstallationThe polyetherimide sheet comes with 3M 468MP adhesive already laminated to the PEI. Apply the PEI with slight pressure and at an angle to prevent and minimize air bubbles. Once applied set the print bed to 60C and apply pressure evenly across the PEI in a sweeping fashion to firmly set the adhesive. Please use a towel to avoid getting burned. Level the bed and set the height of the nozzle before printing.If PEI is installed to the top surface of a bed sandwich (a build plate with multiple layers), it is recommended to install PEI on top of borosilicate glass.UseHeat the bed to the desired temperatures for printing (60 C for PLA and 100 C for ABS). Depending on how thick your bed sandwich is, your set temperature may not be your surface PEI temperature.When the print is completed, let the bed cool, and the part will be easy to release from the PEI surface. Parts are easier to remove if released before the bed becomes completely cold.Leveling the bed is very, very important when using PEI. You want the first layer to be close enough to be squished a little. PETG is an exception and doesn't like squished layers, in which case a Z gap should be used.MaintenanceClean in between prints with isopropyl alcohol. Acetone can be used instead of isopropyl alcohol, but the bed must be cold if acetone is used. Optionally, light sanding with 600-1000 grit sand paper can be done after lots of printing to give the PEI sheet more life.CompatibilityCreality Ender 3 / Creality CR 20 / and more!The Creality Ender 3 and the CR 20 have build volumes of 220 x 220mm with a plate size of 235 x 235mm.Dimensions235mm x 235mm (9.25 x 9.25 inches) PEI thickness: 0.56mm (0.022 inches) 3M 468MP adhesive thickness: 0.13mm (0.005 inches)
2020-07-17 15:25:39
