FAQ

배대지주소

사이즈조견표
주문/배송조회
입금액충전
입출금내역조회
마일리지조회
입금액환불요청
사업자정보등록
1:1문답
자주하는질문과답 FAQ
국제운송료 요율표
해외물류센터주소
사이즈조견표
취소/반품/교환/환불
파손/분실보상
통관/관세
에스크로서비스
개인정보취급방침
이용약관
회사소개
공지사항
찾아오시는길
아마존배송대행신청방법
아마존 홈           
사진확대

Oxlasers 2.5W 3W 5W 7W 450nm Focusable Blue Laser Module Laser Engraver Part DIY Laser Head with PWM (3.5W)
ASIN번호 B07N1BTVN8
상품상태 New   
상품구분 Tools & Home Improvement / Measuring & Layout Tools
브랜드 oxlasers
판매자 미정
판매자위치 미확인
Size
현지 판매 가격
$98.00
상품가격 상세보기
관련상품



상품특징
Make sure this fits by entering your model number.please do not use this on a Arduino board!!!! it is not working with it!!2.5W 3.5W and 5.5W ARE ALL FOCUSABLEFrequency: <15khz, PWM/TTL: 0-5V , Please add a fan when engraving or cutting, in case smoke damage its lens.When you connect laser to your controller board, please pay attention to the pin positions of 12v+ GND- and PWM/TTL, red wire=12V+, black wire=GND-. Yello wire=PWM+, white wire=PWM-(3-4pin wire). So Red Wire must be connected to the 12v+ pin on your controller board’s interface, Black Wire Must be connected to the GND- pin and Yellow Wire must be connected to the PWM/TTL pin, if you use 3-4pin wire, White wire should be connected to the PWM- pin.if your controller board’s laser interface pins are in different position, please change the wires position to make it match the positions of + - PWM of your interface. If the wires connected wrong, it will damage the diode and the driver board.
상품설명
Size:3.5W Technical Parameters: Laser wavelength: 445nm-450nm blue laser Spot type: dotted (adjustable) Output power: 2.5W, 3.5W, 5.5W Size: 2.5W(33*70mm) , 3.5W(33*70mm) 5.5W(40*70mm) Drive mode: external ACC constant current drive Cooling method: forced air cooling Operating voltage: 12V DC Control interface: 2 * 2.54 (TTL control switch, PWM control power) Shell material: aluminum, surface anodized Collimator lens: optical glass coating PACKING LIST: LASER*1 3PIN CABLE*1 3PIN TO 4PIN CABLE*1 SAFETY GLASSES*1
































상품특징
Make sure this fits by entering your model number.please do not use this on a Arduino board!!!! it is not working with it!!2.5W 3.5W and 5.5W ARE ALL FOCUSABLEFrequency: <15khz, PWM/TTL: 0-5V , Please add a fan when engraving or cutting, in case smoke damage its lens.When you connect laser to your controller board, please pay attention to the pin positions of 12v+ GND- and PWM/TTL, red wire=12V+, black wire=GND-. Yello wire=PWM+, white wire=PWM-(3-4pin wire). So Red Wire must be connected to the 12v+ pin on your controller board’s interface, Black Wire Must be connected to the GND- pin and Yellow Wire must be connected to the PWM/TTL pin, if you use 3-4pin wire, White wire should be connected to the PWM- pin.if your controller board’s laser interface pins are in different position, please change the wires position to make it match the positions of + - PWM of your interface. If the wires connected wrong, it will damage the diode and the driver board.
상품설명
Size:3.5W Technical Parameters: Laser wavelength: 445nm-450nm blue laser Spot type: dotted (adjustable) Output power: 2.5W, 3.5W, 5.5W Size: 2.5W(33*70mm) , 3.5W(33*70mm) 5.5W(40*70mm) Drive mode: external ACC constant current drive Cooling method: forced air cooling Operating voltage: 12V DC Control interface: 2 * 2.54 (TTL control switch, PWM control power) Shell material: aluminum, surface anodized Collimator lens: optical glass coating PACKING LIST: LASER*1 3PIN CABLE*1 3PIN TO 4PIN CABLE*1 SAFETY GLASSES*1




























2019-11-30 08:03:15