AUTOOL Pipe Leak Detectors EVAP Leak Tester Machine Automotive Conduit Pipe System Fuel Leak Detector Automotive Fuel Leakage Diagnostic Tester Adjustable Flow Meter for 12V Car Vehicle Boat
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.AUTOOL SDT-206 will detect the leakage of pipe systems on cars, motorcycles, boats.ect.such as fuel pipe, air intake system and cooling tank.AUTOOL SDT-206 will change special oil into smoke, then blow smoke into sealed pipe system. you will find leak point in pipe via the smoke.This upgraded machine now can work on EVAP system (pressure of machine was larger than EVAP request )Inbuilt air compressor,Instant smoke generation. Self-protective system will keep machine away from overload. Combine with adjustable flowmeter and pressure guage,we can adjust output of smoke ,then check leakage level via smoke flow varietyInput :12V DC ; Smoke output value: 6L/min, We offer technical support if needed.
상품설명
Cautions: 1.When you use this detector the first time, please fill 20-30ml oil, not beyond this range. 2.New oil can be filled with only when the smoke is light,and it can't be filled over 15ml every time. 3.Before filling new oil, please pour out the remaining oil in the detector. 4.Please replace the detector oil regularly. Product Information: Power: DC12V, vehicle battery Smoke output value: 6l/min Built-in air supply Controllable flow value How to use: 1.Open the engine cover, and hang the detector in the cover. 2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle. Please secure the other side with a rubber stopple. 3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube. 4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way. 5.Turn on the power switch, and detector starts to work. 6.In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary. 7.After leak detection, please connect well the wires and pipe. 8.Notes: * Please do leak detection away from smoke-sensitive parts. * Do not run the detector over 8 minutes. It needs interval rest. * The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later. * The round parts of this detector is with temperature, be careful to avoid scalding injury. Packing List: 1. Main Unit 2. Hook (with hand-tighten nuts) 3. Smoke output tube 4. Power cable 5. Rubber stopples (with serial specification) 6. Taper stopple 7. Taper pipe 8. 30ml oil bottle 9. User manual
Make sure this fits by entering your model number.AUTOOL SDT-206 will detect the leakage of pipe systems on cars, motorcycles, boats.ect.such as fuel pipe, air intake system and cooling tank.AUTOOL SDT-206 will change special oil into smoke, then blow smoke into sealed pipe system. you will find leak point in pipe via the smoke.This upgraded machine now can work on EVAP system (pressure of machine was larger than EVAP request )Inbuilt air compressor,Instant smoke generation. Self-protective system will keep machine away from overload. Combine with adjustable flowmeter and pressure guage,we can adjust output of smoke ,then check leakage level via smoke flow varietyInput :12V DC ; Smoke output value: 6L/min, We offer technical support if needed.
상품설명
Cautions: 1.When you use this detector the first time, please fill 20-30ml oil, not beyond this range. 2.New oil can be filled with only when the smoke is light,and it can't be filled over 15ml every time. 3.Before filling new oil, please pour out the remaining oil in the detector. 4.Please replace the detector oil regularly. Product Information: Power: DC12V, vehicle battery Smoke output value: 6l/min Built-in air supply Controllable flow value How to use: 1.Open the engine cover, and hang the detector in the cover. 2.Disconnect the pipe that needs to be connected with detector. If the pipe needs to be disconnected in the middle. Please secure the other side with a rubber stopple. 3.Secure this side with proper taper stopple/pipe, and connect it with smoke output tube. 4.Connect detector with DC12V battery: red with positive, black with negative. Do not connect in a contrary way. 5.Turn on the power switch, and detector starts to work. 6.In about 3 minutes, the pipe will be filled with smoke. Check the leak points. Please use head lamp if necessary. 7.After leak detection, please connect well the wires and pipe. 8.Notes: * Please do leak detection away from smoke-sensitive parts. * Do not run the detector over 8 minutes. It needs interval rest. * The detector has protector. If it exceeds working limit, it will power off automatically. In this condition, please operate it later. * The round parts of this detector is with temperature, be careful to avoid scalding injury. Packing List: 1. Main Unit 2. Hook (with hand-tighten nuts) 3. Smoke output tube 4. Power cable 5. Rubber stopples (with serial specification) 6. Taper stopple 7. Taper pipe 8. 30ml oil bottle 9. User manual
2019-04-03 14:23:15