WitBot SKR V1.3 Control Board 32-Bit CPU Equipped with Open Source Firmware Marlin2.0 and Smoothieware and Use Gold Deposition Technology Support TMC2130 TMC2208 DRV8825 A4988 Driver for 3D Printer.
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
1.SKR V1.3 motherboard uses 32-bit main frequency 100MHz ARM-class Cortex-M3 series LPC1768 master chip.Four-Layer Circuit Board,Gold deposition technology,and passed CE certification.2.SKR V1.3 motherboard uses 32-bit main frequency 100MHz ARM-class Cortex-M3 series LPC1768 master chip.Four-Layer Circuit Board,Gold deposition technology,and passed CE certification.3.Support SPI working mode of TMC2130 driver, self-contained material detection function; TMC2130SPI, without using additional limit switch, can realize the function of limit switch by modifying Marin firmware.4.Reserved extended port SERVOS of PWM signal to support BL Touch;Support 2.8-inch and 3.5-inch color touch screens, support 2004 LCD and 12864 LCD.5.If you have any question,please contact us through Amazon:)
상품설명
SKR Motherboard Parameters: Appearance size: 110*85mm Mounting size: 102*76mm Microprocessor: ARM cortex-M3 CPU Input voltage: DC12V-DC24V 5A-15A Motor driver: Support TMC2208UART, TMC2130SPI, ST820, LV8729, DRV8825,A4988, can be independently external motor drive. SKR motherboard power: After the SKR main board is powered on, the red light of the D4 in the lower left corner will light up, indicating that the power supply is normal; the 5V SEL in the middle of the board is the power selection end; 1)When using USB to power the motherboard, connect the +5V and USB pins with a shorting cap. 2)When using 12V-24V power supply, connect the +5V and INT pins with the shorting cap; NOTE :It can be connected to [12V-24V power supply] and [USB] at the same time. The printing process must use the shorting cap to connect the +5V and INT pins. SKR motherboard communicates with computer: The SKR motherboard communicates with the computer through the [USB] interface. After the driver is installed, the motherboard is inserted into the computer to recognize the port for data transmission. It is easy to see that the computer does not recognize the USB port without installing the driver. 1.smoothieware-usb-driver-v1.1 driver installation (Windows systems only) The driver can be obtained from our open source network;(Contact us to get the link) Note: When using smoothieware open source firmware, since only Windows system drivers, the SKR board at this time can only be recognized by the Windows system port! ! ! 2.If you are using Marlin2.0 firmware, follow the tutorial to install;(Contact us to get the link)
1.SKR V1.3 motherboard uses 32-bit main frequency 100MHz ARM-class Cortex-M3 series LPC1768 master chip.Four-Layer Circuit Board,Gold deposition technology,and passed CE certification.2.SKR V1.3 motherboard uses 32-bit main frequency 100MHz ARM-class Cortex-M3 series LPC1768 master chip.Four-Layer Circuit Board,Gold deposition technology,and passed CE certification.3.Support SPI working mode of TMC2130 driver, self-contained material detection function; TMC2130SPI, without using additional limit switch, can realize the function of limit switch by modifying Marin firmware.4.Reserved extended port SERVOS of PWM signal to support BL Touch;Support 2.8-inch and 3.5-inch color touch screens, support 2004 LCD and 12864 LCD.5.If you have any question,please contact us through Amazon:)
상품설명
SKR Motherboard Parameters: Appearance size: 110*85mm Mounting size: 102*76mm Microprocessor: ARM cortex-M3 CPU Input voltage: DC12V-DC24V 5A-15A Motor driver: Support TMC2208UART, TMC2130SPI, ST820, LV8729, DRV8825,A4988, can be independently external motor drive. SKR motherboard power: After the SKR main board is powered on, the red light of the D4 in the lower left corner will light up, indicating that the power supply is normal; the 5V SEL in the middle of the board is the power selection end; 1)When using USB to power the motherboard, connect the +5V and USB pins with a shorting cap. 2)When using 12V-24V power supply, connect the +5V and INT pins with the shorting cap; NOTE :It can be connected to [12V-24V power supply] and [USB] at the same time. The printing process must use the shorting cap to connect the +5V and INT pins. SKR motherboard communicates with computer: The SKR motherboard communicates with the computer through the [USB] interface. After the driver is installed, the motherboard is inserted into the computer to recognize the port for data transmission. It is easy to see that the computer does not recognize the USB port without installing the driver. 1.smoothieware-usb-driver-v1.1 driver installation (Windows systems only) The driver can be obtained from our open source network;(Contact us to get the link) Note: When using smoothieware open source firmware, since only Windows system drivers, the SKR board at this time can only be recognized by the Windows system port! ! ! 2.If you are using Marlin2.0 firmware, follow the tutorial to install;(Contact us to get the link)
2019-04-17 22:30:30