WitBot TMC2208 V2.1 Stepper Motor Driver Module with Heat Sink Upgraded TMC2208 V2.0 DRV8825 Driver Compatible with Ramps1.4 or MKS Board SKR V1.3 for 3D Printers(Pack of 5pcs)
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.TMC2208 V2.1 is a newly upgraded driver module. Puts the chip inside, which is more conducive to heat dissipation.TMC2208 V2.1 is an ultra-quiet two-phase stepper motor driver chip that continuously drives in motion 1.4A current, 2A peak current, 4.75 V-36 V voltage range, 256 subdivision.Compared with TMC2208 V2.0, V2.1 adopts the high quality flat gold finish,which is more stable,has strong oxidation resistance and better heat dissipation.Flexible microPlyer interpolation unit, the component can provide up to 256 microstep / step resolution, even in the wrist frequency system is limited may still be perfect to achieve sinusoidal control; as stealthChop end music technology is widely used in 3D printing, so that these components are also designed to be compatible with current electronic 3D printer, eliminating the need for expensive redesign. Both components have input pulse / direction, can be completely independent operation. ThTMC2208 single-axis chip stepper motor drive, power supply tube built-in pilot current 1.4A peak current 2A, voltage range of 4.75V-36V, 256 subdivision; With the patented spreadCycle technology of high frequency chopper, dcStep , stall stallGuard2 , sensing technology, CoolStep dynamic current regulation technology, can save 70% energy.
상품설명
1.Work mode: PASS / DIR / UART 2. Advantages of the UART modes: 1)The motor current can be arbitrarily set by the firmware; 2)Micro-can be arbitrarily set by the firmware (up to 256 real micro-The real and interpolated micro-can be combined to get the maximum torque; 3)The firmware can dynamically switch the stepper motor between stealthChop2 and spreadCycle mode via the UART; 4)When the motor is not moving, the standby current motor can be dynamically reduced (via the UART) Note: 1.Hardware selection When using the UART operating mode, use a soldering iron carefully to prevent burns and handle after observing, carefully observe whether the module has residual tin slag. It must be cleaned to prevent it.Cause the module to be short-circuited. 2.Pay attention to the line sequence and IO port when wiring. Connecting the wrong line will directly cause the driver to not work.Carefully connected to the above illustration. 3.When plugging the driver into the motherboard, pay attention to see the driving direction, never insert it, and prevent the drive burned. 4.Be sure to do the heat dissipation work (heat sink + cooling fan) before driving to prevent driving. NOTE: Note:If you meet trouble when using it, or if you need to use the instructions, please contact me after placing your order.
Make sure this fits by entering your model number.TMC2208 V2.1 is a newly upgraded driver module. Puts the chip inside, which is more conducive to heat dissipation.TMC2208 V2.1 is an ultra-quiet two-phase stepper motor driver chip that continuously drives in motion 1.4A current, 2A peak current, 4.75 V-36 V voltage range, 256 subdivision.Compared with TMC2208 V2.0, V2.1 adopts the high quality flat gold finish,which is more stable,has strong oxidation resistance and better heat dissipation.Flexible microPlyer interpolation unit, the component can provide up to 256 microstep / step resolution, even in the wrist frequency system is limited may still be perfect to achieve sinusoidal control; as stealthChop end music technology is widely used in 3D printing, so that these components are also designed to be compatible with current electronic 3D printer, eliminating the need for expensive redesign. Both components have input pulse / direction, can be completely independent operation. ThTMC2208 single-axis chip stepper motor drive, power supply tube built-in pilot current 1.4A peak current 2A, voltage range of 4.75V-36V, 256 subdivision; With the patented spreadCycle technology of high frequency chopper, dcStep , stall stallGuard2 , sensing technology, CoolStep dynamic current regulation technology, can save 70% energy.
상품설명
1.Work mode: PASS / DIR / UART 2. Advantages of the UART modes: 1)The motor current can be arbitrarily set by the firmware; 2)Micro-can be arbitrarily set by the firmware (up to 256 real micro-The real and interpolated micro-can be combined to get the maximum torque; 3)The firmware can dynamically switch the stepper motor between stealthChop2 and spreadCycle mode via the UART; 4)When the motor is not moving, the standby current motor can be dynamically reduced (via the UART) Note: 1.Hardware selection When using the UART operating mode, use a soldering iron carefully to prevent burns and handle after observing, carefully observe whether the module has residual tin slag. It must be cleaned to prevent it.Cause the module to be short-circuited. 2.Pay attention to the line sequence and IO port when wiring. Connecting the wrong line will directly cause the driver to not work.Carefully connected to the above illustration. 3.When plugging the driver into the motherboard, pay attention to see the driving direction, never insert it, and prevent the drive burned. 4.Be sure to do the heat dissipation work (heat sink + cooling fan) before driving to prevent driving. NOTE: Note:If you meet trouble when using it, or if you need to use the instructions, please contact me after placing your order.
2019-05-12 07:29:37
