WTKSOY New 2PCS SG402050,51248222913 Trunk Lid Lift Supports Shock Arm Rod For BMW E39 Chasis 5 Series Sedan
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
As for whether your car can use this lift support, you can select your car model in the upper left corner of the page for inquiry or check the description before your purchasing.You can also email us and we will reply within 12 hours.Fitment: Front Hood Lift Supports Struts Compatible With BMW 525i 2001-2006, BMW 528i 1997-2000, BMW 530i 2001-2006, BMW 540i 1997-2003, BMW M5 2000-2003Interchange Part Number:SG402050; 4472; E4472; E95853; 95853; 613673; 613757; 51248222913; 92606032738; 92606032366; 9283HM; 51248222913; 819-5604; 13676;Package include: 2pcs; Placement on Vehicle:Front Gas Charged Lift Supports Struts Shocks Props Arm.SPECIFICATIONS - Actual Extended Length [in] 13.66 ,Compressed Length [in] 9.71
상품설명
WTKSOY is committed to bring you the consumer, the ease and comfort of finding the part you need. Backed by a strong Technical Support , we\'ll take care of your needs and do the research needed to find that hard to find item. Specifications: You will receive 2PCS Rear Gas Lift Supports Struts Bonnet Lift Support for following vehicles. MW 525i 01-06, BMW 528i 97-00, BMW 530i 01-06, BMW 540i 97-03, BMW M5 00-03 Interchange Part Number:SG402050; 4472 E4472 E95853 95853 613673 613757 51248222913 92606032738 92606032366 51248222913; 819-5604 13676 Package Includes: 2pcs x Rear Lift Supports (without screws). How to install : 1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed. 2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length. 3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8", then pull the support away from the vehicle and it will release. 4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur. 5. Lift Supports need to be installed fully extended. In most cases you just can\'t compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support. 6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.
As for whether your car can use this lift support, you can select your car model in the upper left corner of the page for inquiry or check the description before your purchasing.You can also email us and we will reply within 12 hours.Fitment: Front Hood Lift Supports Struts Compatible With BMW 525i 2001-2006, BMW 528i 1997-2000, BMW 530i 2001-2006, BMW 540i 1997-2003, BMW M5 2000-2003Interchange Part Number:SG402050; 4472; E4472; E95853; 95853; 613673; 613757; 51248222913; 92606032738; 92606032366; 9283HM; 51248222913; 819-5604; 13676;Package include: 2pcs; Placement on Vehicle:Front Gas Charged Lift Supports Struts Shocks Props Arm.SPECIFICATIONS - Actual Extended Length [in] 13.66 ,Compressed Length [in] 9.71
상품설명
WTKSOY is committed to bring you the consumer, the ease and comfort of finding the part you need. Backed by a strong Technical Support , we\'ll take care of your needs and do the research needed to find that hard to find item. Specifications: You will receive 2PCS Rear Gas Lift Supports Struts Bonnet Lift Support for following vehicles. MW 525i 01-06, BMW 528i 97-00, BMW 530i 01-06, BMW 540i 97-03, BMW M5 00-03 Interchange Part Number:SG402050; 4472 E4472 E95853 95853 613673 613757 51248222913 92606032738 92606032366 51248222913; 819-5604 13676 Package Includes: 2pcs x Rear Lift Supports (without screws). How to install : 1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed. 2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length. 3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8", then pull the support away from the vehicle and it will release. 4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur. 5. Lift Supports need to be installed fully extended. In most cases you just can\'t compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support. 6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.
2020-01-01 03:41:20