2 Pack ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 with Camera Module OV2640
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 CoreThe ESP32CAM equips the ESP32 with everything necessary to program, run and develop on the wonderchip. Additionally, the board reserved the MPU6050,BME280 and an analog MIC.ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc.Fully compliant with WiFi 802.11b/g/n/e/i and bluetooth 4.2 standards, it can be used as a master mode to build an independent network controller, or as a slave to other host MCUs to add networking capabilities to existing devices.ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an ideal solution for IoT applications.
상품설명
Features: Ultra-small 802.11b/g/n Wi-Fi BT/BLE SoC module Low-power dual-core 32-bit CPU for application processors Up to 240MHz, up to 600 DMIPS Built-in 520 KB SRAM, external 4M PSRAM Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC Support OV2640 and OV7670 cameras with built-in flash Support for images WiFI upload Support TF card Support multiple sleep modes Embedded Lwip and FreeRTOS Support STA/AP/STA AP working mode Support Smart Config/AirKiss One-click distribution network Support for serial local upgrade and remote firmware upgrade (FOTA) Support secondary development Note: 1.Please ensure that the module input power is at least 5V 2A, otherwise the image will unstable. 2.ESP32 GPIO32 pin controls camera power. When the camera is working, please pull GPIO32 low. 3.Since IO0 is connected to the camera XCLK, please leave IO0 floating when using it. Do not connect high and low level. 4.The factory has the default firmware, no additional download is available. Please handle it carefully if you need to re-burn other firmware. Package Included: 2 x ESP32-CAM Module 2 x Camera Module OV2640 2MP
Make sure this fits by entering your model number.The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 CoreThe ESP32CAM equips the ESP32 with everything necessary to program, run and develop on the wonderchip. Additionally, the board reserved the MPU6050,BME280 and an analog MIC.ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc.Fully compliant with WiFi 802.11b/g/n/e/i and bluetooth 4.2 standards, it can be used as a master mode to build an independent network controller, or as a slave to other host MCUs to add networking capabilities to existing devices.ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an ideal solution for IoT applications.
상품설명
Features: Ultra-small 802.11b/g/n Wi-Fi BT/BLE SoC module Low-power dual-core 32-bit CPU for application processors Up to 240MHz, up to 600 DMIPS Built-in 520 KB SRAM, external 4M PSRAM Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC Support OV2640 and OV7670 cameras with built-in flash Support for images WiFI upload Support TF card Support multiple sleep modes Embedded Lwip and FreeRTOS Support STA/AP/STA AP working mode Support Smart Config/AirKiss One-click distribution network Support for serial local upgrade and remote firmware upgrade (FOTA) Support secondary development Note: 1.Please ensure that the module input power is at least 5V 2A, otherwise the image will unstable. 2.ESP32 GPIO32 pin controls camera power. When the camera is working, please pull GPIO32 low. 3.Since IO0 is connected to the camera XCLK, please leave IO0 floating when using it. Do not connect high and low level. 4.The factory has the default firmware, no additional download is available. Please handle it carefully if you need to re-burn other firmware. Package Included: 2 x ESP32-CAM Module 2 x Camera Module OV2640 2MP
2021-01-06 23:56:18