OXLasers 520NM 1W Focusable Green Laser Module High Power DIY 12V 1000mW DIY Laser Head with PWM TTL
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Wave Length: 520nm, Output: 1000mW, Beam Diameter: about 5mm, Very bright! Duty Cycle: 2 hours on, 1 hours off.Frequency: <15khz, PWM/TTL: 0-5V , as you may know , this laser is not made for engraving, if you want a engraving laser, please chose a blue one. this one can only engraving on dark color paperWhen you connect laser to your controller board for engraving, please pay attention to the pin positions of 12v+ GND- and PWM/TTL, red wire=12V+, black wire=GND-. Yello wire=PWM+, white wire=PWM-(3-4pin wire). So Red Wire must be connected to the 12v+ pin on your controller board’s interface, Black Wire Must be connected to the GND- pin and Yellow Wire must be connected to the PWM/TTL pin, if you use 3-4pin wire, White wire should be connected to the PWM- pin.if your controller board’s laser interface pins are in different position, please change the wires position to make it match the positions of + - PWM of your interface. If the wires connected wrong, it will damage the diode and the driver board. Please add a fan when engraving or cutting, in case smoke damage its lens.This laser comes with 12V 2A DC adapter , you can connect it to 110-240V power source directly. please wear safety glasses when using!!!
상품설명
Technical Parameters: Laser wavelength: 520nm Spot type: retangular dotted (adjustable) Output power: 1000mW Size: (33*70mm) Drive mode: external ACC constant current drive Cooling method: forced air cooling Operating voltage: 12V DC Control interface: 3pin (12V+ GND- PWM) Shell material: aluminum, surface anodized Collimator lens: optical glass coating PACKING LIST: LASER*1 3PIN CABLE*1 3PIN TO 4PIN CABLE*1 DC to 3pin Connector 12V 2A AC/DC Adapter SAFETY GLASSES*1
Make sure this fits by entering your model number.Wave Length: 520nm, Output: 1000mW, Beam Diameter: about 5mm, Very bright! Duty Cycle: 2 hours on, 1 hours off.Frequency: <15khz, PWM/TTL: 0-5V , as you may know , this laser is not made for engraving, if you want a engraving laser, please chose a blue one. this one can only engraving on dark color paperWhen you connect laser to your controller board for engraving, please pay attention to the pin positions of 12v+ GND- and PWM/TTL, red wire=12V+, black wire=GND-. Yello wire=PWM+, white wire=PWM-(3-4pin wire). So Red Wire must be connected to the 12v+ pin on your controller board’s interface, Black Wire Must be connected to the GND- pin and Yellow Wire must be connected to the PWM/TTL pin, if you use 3-4pin wire, White wire should be connected to the PWM- pin.if your controller board’s laser interface pins are in different position, please change the wires position to make it match the positions of + - PWM of your interface. If the wires connected wrong, it will damage the diode and the driver board. Please add a fan when engraving or cutting, in case smoke damage its lens.This laser comes with 12V 2A DC adapter , you can connect it to 110-240V power source directly. please wear safety glasses when using!!!
상품설명
Technical Parameters: Laser wavelength: 520nm Spot type: retangular dotted (adjustable) Output power: 1000mW Size: (33*70mm) Drive mode: external ACC constant current drive Cooling method: forced air cooling Operating voltage: 12V DC Control interface: 3pin (12V+ GND- PWM) Shell material: aluminum, surface anodized Collimator lens: optical glass coating PACKING LIST: LASER*1 3PIN CABLE*1 3PIN TO 4PIN CABLE*1 DC to 3pin Connector 12V 2A AC/DC Adapter SAFETY GLASSES*1
2019-11-24 19:48:35