100mm stainless steel Adjustable Film Coating Applicator Film Coater with Micrometer Wet Film Preparation Device (removable magnetic suction film casting doctor blade)
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.? The new model is on the market, stainless steel material adjustable film applicator, using the latest magnetic absorption control technology, beautiful and more durable, anti-wear and corrosion resistance, your experimental film making a good choice!? The KTQ-III adjustable fabricator is suitable for the study of accurate evaluation of thin film thickness. By adjusting the two differentiators above the fabricator, it can adjust the scraper below to control the gap, that is, the final coating thickness.? The operator sets the blade clearance by adjusting the micrometers and sets up film width to be coated by adjusting blade width. This is an excellent tool to make the quality film for material research laboratories to make ceramic tape casting, battery electrodes, and various coating at the lower cost.? Major Manufacturing Material: Aluminum Alloy.；Scratch Effective Width: 55/100/150/200mm.;Film thickness range: 0 ~ 3500μm.;Accuracy: ±2 micron. Stainless steel knife blade with precision ground edge.;Micrometer head's controllable accuracy is 10 microns.? Widely used in: printing, paint, paint, cosmetics, drugs, adhesives, batteries and other scientific research industries.
상품설명
Usage method: 1. Place the coater on a completely flat test surface and adjust the clearance required by the scraper to twice the thickness of the required wet film. 2. In the front section of the coated knife, a small amount of test samples are poured between the end plates, and the instrument is moved on the surface at a slow and uniform speed of about 1-2 cm per second until the liquid has been fully coated and/or any remaining liquid has been removed from the end of the coated path. 3. The exact ratio of wet film thickness to any clearance of the coated knife depends on the material used, the viscosity and texture of the liquid, the pressure applied on the coated knife, the speed of the coated film and the geometric shape of the edge of the coated film. 4. The actual wet film should be measured by a wet film thickness gauge, and the gap should be adjusted until the required wet film thickness is reached. Maintenance and maintenance: 1. Clean the instrument with appropriate solvents immediately after each use. 2. Both ends of the scraper move in the groove. The groove must be kept free of sample material at all times. 3. Differential heads may occasionally need to be repositioned. To correct wear or dislocation, components must be lowered or raised, which can be achieved by loosening (and removing) two hidden fixed screws on each differentiator. It takes about 7 days for all our products to reach the designated address by DHL.
Make sure this fits by entering your model number.? The new model is on the market, stainless steel material adjustable film applicator, using the latest magnetic absorption control technology, beautiful and more durable, anti-wear and corrosion resistance, your experimental film making a good choice!? The KTQ-III adjustable fabricator is suitable for the study of accurate evaluation of thin film thickness. By adjusting the two differentiators above the fabricator, it can adjust the scraper below to control the gap, that is, the final coating thickness.? The operator sets the blade clearance by adjusting the micrometers and sets up film width to be coated by adjusting blade width. This is an excellent tool to make the quality film for material research laboratories to make ceramic tape casting, battery electrodes, and various coating at the lower cost.? Major Manufacturing Material: Aluminum Alloy.；Scratch Effective Width: 55/100/150/200mm.;Film thickness range: 0 ~ 3500μm.;Accuracy: ±2 micron. Stainless steel knife blade with precision ground edge.;Micrometer head's controllable accuracy is 10 microns.? Widely used in: printing, paint, paint, cosmetics, drugs, adhesives, batteries and other scientific research industries.
상품설명
Usage method: 1. Place the coater on a completely flat test surface and adjust the clearance required by the scraper to twice the thickness of the required wet film. 2. In the front section of the coated knife, a small amount of test samples are poured between the end plates, and the instrument is moved on the surface at a slow and uniform speed of about 1-2 cm per second until the liquid has been fully coated and/or any remaining liquid has been removed from the end of the coated path. 3. The exact ratio of wet film thickness to any clearance of the coated knife depends on the material used, the viscosity and texture of the liquid, the pressure applied on the coated knife, the speed of the coated film and the geometric shape of the edge of the coated film. 4. The actual wet film should be measured by a wet film thickness gauge, and the gap should be adjusted until the required wet film thickness is reached. Maintenance and maintenance: 1. Clean the instrument with appropriate solvents immediately after each use. 2. Both ends of the scraper move in the groove. The groove must be kept free of sample material at all times. 3. Differential heads may occasionally need to be repositioned. To correct wear or dislocation, components must be lowered or raised, which can be achieved by loosening (and removing) two hidden fixed screws on each differentiator. It takes about 7 days for all our products to reach the designated address by DHL.
2020-08-08 03:03:37
