BZ 3D Controller Board MKS SGen L V1.0 32-bit Motherboard Compatible Uart/SPI Open Source Marlin2.0/Smoothieware with MKS TMC2208/2209 Steep Motor Driver for 3D Printer Parts (Board+TMC2208 V2.05)
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.★Adopt 32-bit Cortex-M3 LPC 1768 chip, 100MHZ frequency, strong computing power, performance greatly improved.In-line and external driver port, more expandable and selective.★Compatible with multiple drivers and special modes (TMC2208 UART mode, TMC2130 SPI mode, etc.),dedicated port reservation, convenient for wiring settings.Use high-quality PCB, and the corresponding pins of each interface are marked with silk screen for easier identification and modification.Using a dedicated power chip, support 12V-24V current input.★It is compatible with multiple LCD screens.Compatible with all of MKS TFT touch screens.Support lots of open-source firmwares, including smoothie-ware and Marlin V2.0.Compatible with multiple drivers and special modes (TMC2208 UART mode, TMC2130 SPI mode, etc.)★Compared to the TMC2100 stepper motor driver module, TMC2208 driver module is with lower heat. The heat of TMC2208 in 0.8A with the equivalent effect of the TMC2100 heat in 0.5A , can be used interchangeably with the TMC2100.★Support uart mode by set jumper caps instead of welding on MKS SGEN L (No jumper is needed, no welding drive is required, and it is more convenient to use)
상품설명
Style:Board+TMC2208 V2.0*5 Input voltage: 12V-24V Support Print format: G-code MPU: Cortex-M3 100MHZ Support Display:MKS TFT24/28/32/35 ect Support machine:XYZ、 delta、 kossel、 Ultimaker、 corey Supports multiple FDM 3D Printers ★Packing List: 1* MKS SGEN L V1.0 +5*TMC2208+1*USB Cable+20*Jumper caps ★Drive mode setting There are three drive mode settings: normal mode, UART mode and SPI mode.Please refer to the picture Note: The following drive settings are based on the mks series drive, and different brand drive setup methods may be set differently. ★Printing connection and driver installation If it needs to connect computer to print, the computer needs to be installed a USB driver to recognized the COM port. Note: only update the motherboard firmware, can motherboard COM port be recognized by computer. The USB driver of Smoothieware can be download and install via official website, or get zipped files from customer service staffs and technicians ★MARLIN2.0 firmware If the marlin firmware is updated, but the computer recognizes it as an unknown device, you can right-click to select the update driver and select the path to update the driver. ★If you need more detailed information on changing the firmware, how to use the board and MKS series drivers and displays, please contact me.
Make sure this fits by entering your model number.★Adopt 32-bit Cortex-M3 LPC 1768 chip, 100MHZ frequency, strong computing power, performance greatly improved.In-line and external driver port, more expandable and selective.★Compatible with multiple drivers and special modes (TMC2208 UART mode, TMC2130 SPI mode, etc.),dedicated port reservation, convenient for wiring settings.Use high-quality PCB, and the corresponding pins of each interface are marked with silk screen for easier identification and modification.Using a dedicated power chip, support 12V-24V current input.★It is compatible with multiple LCD screens.Compatible with all of MKS TFT touch screens.Support lots of open-source firmwares, including smoothie-ware and Marlin V2.0.Compatible with multiple drivers and special modes (TMC2208 UART mode, TMC2130 SPI mode, etc.)★Compared to the TMC2100 stepper motor driver module, TMC2208 driver module is with lower heat. The heat of TMC2208 in 0.8A with the equivalent effect of the TMC2100 heat in 0.5A , can be used interchangeably with the TMC2100.★Support uart mode by set jumper caps instead of welding on MKS SGEN L (No jumper is needed, no welding drive is required, and it is more convenient to use)
상품설명
Style:Board+TMC2208 V2.0*5 Input voltage: 12V-24V Support Print format: G-code MPU: Cortex-M3 100MHZ Support Display:MKS TFT24/28/32/35 ect Support machine:XYZ、 delta、 kossel、 Ultimaker、 corey Supports multiple FDM 3D Printers ★Packing List: 1* MKS SGEN L V1.0 +5*TMC2208+1*USB Cable+20*Jumper caps ★Drive mode setting There are three drive mode settings: normal mode, UART mode and SPI mode.Please refer to the picture Note: The following drive settings are based on the mks series drive, and different brand drive setup methods may be set differently. ★Printing connection and driver installation If it needs to connect computer to print, the computer needs to be installed a USB driver to recognized the COM port. Note: only update the motherboard firmware, can motherboard COM port be recognized by computer. The USB driver of Smoothieware can be download and install via official website, or get zipped files from customer service staffs and technicians ★MARLIN2.0 firmware If the marlin firmware is updated, but the computer recognizes it as an unknown device, you can right-click to select the update driver and select the path to update the driver. ★If you need more detailed information on changing the firmware, how to use the board and MKS series drivers and displays, please contact me.
2020-01-31 22:05:57