Yamix Water-Cooled Gasoline Combustion Engine Hit, Horizontal Miss Complete Engine with Hand Starter
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Its a horizontal gasoline model engine, with water cooling ancient structure. The engine cylinder head design is unique, the valve mechanism is installed on the left sideThe processing difficulty of side valve structure also increases, through the compact side gear drive mechanism to control the exhaust shutdownA 90 degree helical gear is usedThe flywheel on the left is equipped with a speed limiter connected to a large bevel in the middleProduct Size: 18 x 12.5 x 12.5cm
상품설명
Engine startup steps: 1. Open the bottom plate to check the wiring of the engine, connect the fuel tank pipe, and install the three AA batteries to close the bottom plate. 2. Fill the fuel tank with gasoline (95). When the flling is completed, make sure there is no air in the oil pipe. 3, On the right side of the engine (installation of the flying hammer position), slowly turn counterclockwise by hand to buy more than one turn, its role can make the mixed gasoline fully enter the cylinder. 4. Turn on the power switch and turn the flywheel to start the engine counterclockwise on the right side of the engine (installation of the flying hammer position). Precautions: 1. If the ignition device is normal and the cylinder is under normal compression, if the machine still does not start normally, it is very likely that the carburetor needle should be adjusted. 2. Screw the screw on the top of the carburetor, then loosen 1/4 turn, start the flywheel. This can be done several times to make the mixing ratio of gasoline and air Specifications: Material: Brass + Stainless Steel + Wood Item: Horizontal Hit and Miss Complete Engine No.: M94 Wooden Base: 180 x 66 x 50mm Displacement: 6CC Cylinder Diameter: 22mm Stroke: 20mm Revolutions: Approximately 1200rpm Power Supply: 3 x AA batteries (Not Included) Fuel: 95 Gasoline Product Weight: 1610g Package Content: 1 x Model Engine 1 x Hand Starter 1 x Manual
Make sure this fits by entering your model number.Its a horizontal gasoline model engine, with water cooling ancient structure. The engine cylinder head design is unique, the valve mechanism is installed on the left sideThe processing difficulty of side valve structure also increases, through the compact side gear drive mechanism to control the exhaust shutdownA 90 degree helical gear is usedThe flywheel on the left is equipped with a speed limiter connected to a large bevel in the middleProduct Size: 18 x 12.5 x 12.5cm
상품설명
Engine startup steps: 1. Open the bottom plate to check the wiring of the engine, connect the fuel tank pipe, and install the three AA batteries to close the bottom plate. 2. Fill the fuel tank with gasoline (95). When the flling is completed, make sure there is no air in the oil pipe. 3, On the right side of the engine (installation of the flying hammer position), slowly turn counterclockwise by hand to buy more than one turn, its role can make the mixed gasoline fully enter the cylinder. 4. Turn on the power switch and turn the flywheel to start the engine counterclockwise on the right side of the engine (installation of the flying hammer position). Precautions: 1. If the ignition device is normal and the cylinder is under normal compression, if the machine still does not start normally, it is very likely that the carburetor needle should be adjusted. 2. Screw the screw on the top of the carburetor, then loosen 1/4 turn, start the flywheel. This can be done several times to make the mixing ratio of gasoline and air Specifications: Material: Brass + Stainless Steel + Wood Item: Horizontal Hit and Miss Complete Engine No.: M94 Wooden Base: 180 x 66 x 50mm Displacement: 6CC Cylinder Diameter: 22mm Stroke: 20mm Revolutions: Approximately 1200rpm Power Supply: 3 x AA batteries (Not Included) Fuel: 95 Gasoline Product Weight: 1610g Package Content: 1 x Model Engine 1 x Hand Starter 1 x Manual
2020-10-24 10:40:50