TinySA Spectrum Analyzer, Antenna Analyzer Ham Radio, Handheld MF/HF/VHF UHF, RF Explorer Audio Spectrum Analyzer
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Dual input and output: 0.1MHz-350MHz low-quality MF/HF/VHF input, 240MHz-960MHz high-quality lower UHF input. Band-pass filter with switchable resolution, suitable for the range between 2.6KHz and 640KHz2.8 inch TFT color display: it can display 290 scanning points, covering the entire low or high frequency range. The input step attenuator for MF/HF/VHF input is 0dB to 31dBWith signal generator function: when not used as a spectrum analyzer, it can be used as a signal generator, MF / HF / VHF sine wave output between 0.1MHz-350MHz, UHF square wave output between 240MHz-960MHzConnect to PC via USB, it becomes PC controlled spectrum analyzer.Rechargeable battery, can be carried for at least 2 hours
상품설명
User interface: Display resolution 320*240 pixels Screen diagonal 2.8" 16 bits per RGB pixels Resistive touching control Jog switch control USB serial port control Optional TTL USART port (SW not yet implemented) on the internal PCB Linear power supply to refrain switching noise The input/output specification of the tinySA is split over the 4 modes. Low input mode spec: Input frequency range from 100KHz to 350MHz. Input impedance 50 ohm when input attenuation set to 10dB or more. Selectable manual and automatic input attenuation between 0dB and 31dB in 1dB steps. Absolute maximum input level without attenuation of +10dBm. Absolute maximum input power with 30dB attenuation of +20dBm for short period. Input intercept point of third order modulation products (IIP3) with 0dB attenuation of +15dBm. 1dB compression point at +2dBm with 0dB attenuation. Power detector resolution of 0.5dB and linearity ver-sus frequency of +/-1dB. Absolute power level accuracy after power level calibration of +/-1dB. Lowest discernible signal using a resolution bandwidth of 30KHz of -102dBm. Frequency accuracy equal to the selected resolution bandwidth. Phase noise of -90dB/Hz at 100KHz offset and -115dB/Hz at 1MHz offset. Spur free dynamic range when using a 30KHz resolution bandwidth of 70dB. Manually selectable resolution filters of 3, 10, 30, 100, 300, 600KHz. Automatic selection of one of the 57 resolution filters. On screen resolution of 51, 101, 145 or 290 measurement points. Scanning speed of over 1000 points/second using largest resolution filters. Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth.
Make sure this fits by entering your model number.Dual input and output: 0.1MHz-350MHz low-quality MF/HF/VHF input, 240MHz-960MHz high-quality lower UHF input. Band-pass filter with switchable resolution, suitable for the range between 2.6KHz and 640KHz2.8 inch TFT color display: it can display 290 scanning points, covering the entire low or high frequency range. The input step attenuator for MF/HF/VHF input is 0dB to 31dBWith signal generator function: when not used as a spectrum analyzer, it can be used as a signal generator, MF / HF / VHF sine wave output between 0.1MHz-350MHz, UHF square wave output between 240MHz-960MHzConnect to PC via USB, it becomes PC controlled spectrum analyzer.Rechargeable battery, can be carried for at least 2 hours
상품설명
User interface: Display resolution 320*240 pixels Screen diagonal 2.8" 16 bits per RGB pixels Resistive touching control Jog switch control USB serial port control Optional TTL USART port (SW not yet implemented) on the internal PCB Linear power supply to refrain switching noise The input/output specification of the tinySA is split over the 4 modes. Low input mode spec: Input frequency range from 100KHz to 350MHz. Input impedance 50 ohm when input attenuation set to 10dB or more. Selectable manual and automatic input attenuation between 0dB and 31dB in 1dB steps. Absolute maximum input level without attenuation of +10dBm. Absolute maximum input power with 30dB attenuation of +20dBm for short period. Input intercept point of third order modulation products (IIP3) with 0dB attenuation of +15dBm. 1dB compression point at +2dBm with 0dB attenuation. Power detector resolution of 0.5dB and linearity ver-sus frequency of +/-1dB. Absolute power level accuracy after power level calibration of +/-1dB. Lowest discernible signal using a resolution bandwidth of 30KHz of -102dBm. Frequency accuracy equal to the selected resolution bandwidth. Phase noise of -90dB/Hz at 100KHz offset and -115dB/Hz at 1MHz offset. Spur free dynamic range when using a 30KHz resolution bandwidth of 70dB. Manually selectable resolution filters of 3, 10, 30, 100, 300, 600KHz. Automatic selection of one of the 57 resolution filters. On screen resolution of 51, 101, 145 or 290 measurement points. Scanning speed of over 1000 points/second using largest resolution filters. Automatic optimization of actual scanning points to ensure coverage of the whole scan range regardless of the chosen resolution bandwidth.
2020-12-30 12:28:55
