Automatic Rebar Tying Machine, 8-34mm Hand Held Rebar Bender Machine, for Civil Building, Foor Pipe, Heating Floor Mesh, Steel Bar w/Pliers+ Charger (Blue)
|
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Labor-saving -- Compact size, lightweight, easy to grab. It can save 3-5 times than man power by hand. Reasonable structure, advanced craft, simple and convenient operation, high efficiency and convenient maintenance.Performance -- It is a miniature motor tool has the trait of safety and credibility. Rebar Tier is a hand held machine used to pack rebars quickly.Specifications -- Material: Plastic + Metal; Voltage: 12V; Battery: Lithium Ion Batteries; Battery Capacity: 1500 mAh; Battery Charging Time: 1.5 hours full filling; Tying Wire Diameter: 0.8mm; Tying Wire Length: more than 110 m; Applicable Scope Of Steel Strapping: 8mm - 34mm; Knot Wire Length: 300 - 500mm; Knot Number Per Charge: 1500 times; Knot The Required Time: 0.8 seconds at a time; Machine Size: 275 mm * 65 mm * 240 mm / 10.83''x2.56''x9.45''(appr.)Operating Skills -- 1. In use, the left tilt 45 degrees after banding, the next time the banding into a right tilt 45 degrees banding, left and right alternately banding. 2. When the machine is about to tighten, the machine will appear slightly shaking, while holding the hand of the machine not too tight, you can relax properly.Package -- 1X Tying Machine; 1X Pliers; 1X Charger; 1X Storage Box; 2X Lithium Ion Batteries; 1X Tying Wire in the machine (Tying Wire Standard: About 0.8 mm x 110 m/roll).
상품설명
Color:Blue Product Description Tying Wire Installations： 1. In the state of start-up, press the locking plate of the opening wire plate, open the plate cover. 2. Take out the tying wire, tear the packaging film, pull straight wire head about 10 cm, load into the binding machine in the clockwise direction, the wire head into the guide tap tube. Note: Clench the wire plate when tear the packaging film, do not let the wire loose. If the wire is free to disperse, it will lead to the spread of the wire stuck in the wire plate. 3. Insert the head of the wire guide into the tap pipe until it is resisted. 4. Cover the plate and fasten the locking piece. 5. Pinch the wire forward with two fingers, press and hold the switch and send the wire out. 6. If you want to take out the wire plate when finished, press and hold the locking piece, open the wire plate cover plate, holding the wire tray to the side and pull out. Operation Instructions： 1. The rebar tirer's jaws are stuck to the intersection of the steel bars, and the steel bars are hooked at 45 degree angles. Note: There can be no barrier between the mouth of the jaws and the wire. 2. Press the start switch, the rebar tirer machine carries on the work (spins, hinges tightly, cuts off) Note: Press one button at a time, do not probe the jaws at work. 3. When automatic completion, the jaw from the steel bar intersection and then pull back, complete the process and prepare for the next binding. 4. When the binding process is not completed, do not unplug the machine in advance, otherwise it will cause the bundling of the goods tied skidding. Maintenance： 1. Clean the machine regularly, keep the wire mouth clean. 2. Batteries must not be placed together with other metal objects to avoid short circuit. 3. Non-professional do not disassemble the machine arbitrarily, lest cause damage.
Make sure this fits by entering your model number.Labor-saving -- Compact size, lightweight, easy to grab. It can save 3-5 times than man power by hand. Reasonable structure, advanced craft, simple and convenient operation, high efficiency and convenient maintenance.Performance -- It is a miniature motor tool has the trait of safety and credibility. Rebar Tier is a hand held machine used to pack rebars quickly.Specifications -- Material: Plastic + Metal; Voltage: 12V; Battery: Lithium Ion Batteries; Battery Capacity: 1500 mAh; Battery Charging Time: 1.5 hours full filling; Tying Wire Diameter: 0.8mm; Tying Wire Length: more than 110 m; Applicable Scope Of Steel Strapping: 8mm - 34mm; Knot Wire Length: 300 - 500mm; Knot Number Per Charge: 1500 times; Knot The Required Time: 0.8 seconds at a time; Machine Size: 275 mm * 65 mm * 240 mm / 10.83''x2.56''x9.45''(appr.)Operating Skills -- 1. In use, the left tilt 45 degrees after banding, the next time the banding into a right tilt 45 degrees banding, left and right alternately banding. 2. When the machine is about to tighten, the machine will appear slightly shaking, while holding the hand of the machine not too tight, you can relax properly.Package -- 1X Tying Machine; 1X Pliers; 1X Charger; 1X Storage Box; 2X Lithium Ion Batteries; 1X Tying Wire in the machine (Tying Wire Standard: About 0.8 mm x 110 m/roll).
상품설명
Color:Blue Product Description Tying Wire Installations： 1. In the state of start-up, press the locking plate of the opening wire plate, open the plate cover. 2. Take out the tying wire, tear the packaging film, pull straight wire head about 10 cm, load into the binding machine in the clockwise direction, the wire head into the guide tap tube. Note: Clench the wire plate when tear the packaging film, do not let the wire loose. If the wire is free to disperse, it will lead to the spread of the wire stuck in the wire plate. 3. Insert the head of the wire guide into the tap pipe until it is resisted. 4. Cover the plate and fasten the locking piece. 5. Pinch the wire forward with two fingers, press and hold the switch and send the wire out. 6. If you want to take out the wire plate when finished, press and hold the locking piece, open the wire plate cover plate, holding the wire tray to the side and pull out. Operation Instructions： 1. The rebar tirer's jaws are stuck to the intersection of the steel bars, and the steel bars are hooked at 45 degree angles. Note: There can be no barrier between the mouth of the jaws and the wire. 2. Press the start switch, the rebar tirer machine carries on the work (spins, hinges tightly, cuts off) Note: Press one button at a time, do not probe the jaws at work. 3. When automatic completion, the jaw from the steel bar intersection and then pull back, complete the process and prepare for the next binding. 4. When the binding process is not completed, do not unplug the machine in advance, otherwise it will cause the bundling of the goods tied skidding. Maintenance： 1. Clean the machine regularly, keep the wire mouth clean. 2. Batteries must not be placed together with other metal objects to avoid short circuit. 3. Non-professional do not disassemble the machine arbitrarily, lest cause damage.
2021-03-12 13:04:02
