V11 Iron VISOR TINT DECAL Graphic Sticker Helmet Fits: Icon Shoei Bell HJC Oneal Scorpion AGV V2
|
상품가격 상세보기
이벤트보기
|
- 상품상세정보
상품특징
Make sure this fits by entering your model number.Helmet Visor Decal Fits: Icon Shoei Bell HJC Oneal Scorpion AGV & MoreSee Through Perforated Technology - Image on the outside, See through on the insideEasy to apply. Removable without damage - Peel and stick application - Does NOT include helmet or visor (Decal Only)For show use, or passenger helmet only. Not recommended for street use.Universal Size (See sizing below)
상품설명
19.5" x 8" See through Visor tint graphics are easy to apply and will add an amazing custom look to any helmet. It can be used on a wide variety of helmet visors. Please measure your visor to insure the item will fit BEFORE buying. (Graphics should be slightly over sized to allow the whole visor to be covered, then trimmed around the edge with a razor or hobby knife for a perfect seamless fit). We have a large variety of other images. Please feel free to check our other designs. You will receive the design shown in the title and main picture above. SIZING: The measurements of this item are 19.5" x 8" Which will fit MOST visors. Please measure your visor BEFORE ordering to make sure the size provided will work. We can also slightly alter the sizes to suite your needs. Please contact us in an AMAZON message with the size you would need it produced and we will contact you back and let you know if we can make it that size. There is usually no extra charge to alter a size (Even if it is bigger). WE CAN NOT ACCEPT RETURNS OR EXCHANGES DUE TO SIZING ISSUES..... APPLICATION INSTRUCTIONS: (1) Clean surface of any dust or debris. Alcohol is recommended. (make sure surface is dry) (2) Place decal on a flat surface face down and peel off paper backing, *IMPORTANT* Avoid letting the decal stick to its self (3) Tack down just the center of the decal from top to bottom with your finger, and let the left and right area hang without touching. Start with one side, while holding the decal away from touching the visor (but still tacked down in the middle) Lightly heat the decal with a heat gun or hair dryer. When the decal is warm keep the decal tight by pulling up and down on it at the same time as you wrap it around the side. Repeat on the other side (4) Trim the excess material off along the edge of the visor with a razor or hobby knife.
Make sure this fits by entering your model number.Helmet Visor Decal Fits: Icon Shoei Bell HJC Oneal Scorpion AGV & MoreSee Through Perforated Technology - Image on the outside, See through on the insideEasy to apply. Removable without damage - Peel and stick application - Does NOT include helmet or visor (Decal Only)For show use, or passenger helmet only. Not recommended for street use.Universal Size (See sizing below)
상품설명
19.5" x 8" See through Visor tint graphics are easy to apply and will add an amazing custom look to any helmet. It can be used on a wide variety of helmet visors. Please measure your visor to insure the item will fit BEFORE buying. (Graphics should be slightly over sized to allow the whole visor to be covered, then trimmed around the edge with a razor or hobby knife for a perfect seamless fit). We have a large variety of other images. Please feel free to check our other designs. You will receive the design shown in the title and main picture above. SIZING: The measurements of this item are 19.5" x 8" Which will fit MOST visors. Please measure your visor BEFORE ordering to make sure the size provided will work. We can also slightly alter the sizes to suite your needs. Please contact us in an AMAZON message with the size you would need it produced and we will contact you back and let you know if we can make it that size. There is usually no extra charge to alter a size (Even if it is bigger). WE CAN NOT ACCEPT RETURNS OR EXCHANGES DUE TO SIZING ISSUES..... APPLICATION INSTRUCTIONS: (1) Clean surface of any dust or debris. Alcohol is recommended. (make sure surface is dry) (2) Place decal on a flat surface face down and peel off paper backing, *IMPORTANT* Avoid letting the decal stick to its self (3) Tack down just the center of the decal from top to bottom with your finger, and let the left and right area hang without touching. Start with one side, while holding the decal away from touching the visor (but still tacked down in the middle) Lightly heat the decal with a heat gun or hair dryer. When the decal is warm keep the decal tight by pulling up and down on it at the same time as you wrap it around the side. Repeat on the other side (4) Trim the excess material off along the edge of the visor with a razor or hobby knife.
2022-06-24 01:42:27