Throttle Body For Nissan Sentra Tiida Versa 1.8L NV200 Sentra 2.0L 16119ET000
닛산 센트라 티이다 베르사 1.8L NV200 센트라 2.0L 16119 스로틀 바디ET000
| 상품번호 | 256243642319 |
| 상태 | New |
| 거래유형 | 즉시구매 |
| 출고국 | 미국 (US) |
상품 설명
|
|
|
|
|
|
|
|
|
|
Fits Applications
For Nissan Cube 1.8L 2009-2014
For Nissan NV200 2.0L 2013-2021
For Nissan Sentra 1.8L 2013-2019
For Nissan Sentra 2.0L 2007-2012
For Nissan Tiida 1.8L 2007-2014
For Nissan Versa 1.8L 2007-2012
Electronic Throttle Body the usual parts
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
The mechanic will replace the throttle body on your car if:
- It can’t be cleaned properly.
- The throttle flap, throttle shaft, or the mechanical linkages to the throttle cable are damaged.
- The electronic throttle actuator is faulty.
- There is a damaged throttle body or TP sensor electrical connector.
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
- A faulty throttle position sensor
- Gas pedal sensor problems
- Intake manifold pressure sensor issues
- A clogged air filter
- A bad Mass Airflow sensor (MAF sensor)
- A failing fuel pump
- A malfunctioning fuel injector
- A defective fuel pressure regulator
- These parts can cause problems similar to bad throttle body symptoms.
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers.
Throttle Body Replacement
1. Refer to the service manual for identification and location of the throttle body.
2. Remove the air intake duct from the throttle body once it is located.
3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement.
4. Pull out the cables from the throttle body.
5. Remove the hoses such as air or vacuum hoses from the throttle body.
6. Disconnect the throttle position sensor.
7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything.
9. Properly clean the assembly and port to remove any carbon build up.
10. Compare the old throttle body with the new one.
11. Install the throttle body in the port.
12. Fasten the bolts and screws to hold it in place.
13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body.
15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn?
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need?
Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required?
As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
- Disconnecting a battery cable
- A battery dies
- Replacing a battery
- Clearing the check engine light
- Replace an electronic throttle body
- Cleaning an electronic throttle body in an inappropriate way
- etc…
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn?
In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire).
If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn?
Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
Fits Applications
For Nissan Cube 1.8L 2009-2014
For Nissan NV200 2.0L 2013-2021
For Nissan Sentra 1.8L 2013-2019
For Nissan Sentra 2.0L 2007-2012
For Nissan Tiida 1.8L 2007-2014
For Nissan Versa 1.8L 2007-2012
Electronic Throttle Body the usual parts
- Throttle position sensor
- Flange
- Butterfly valve
- Throttle control valve
- Accelerator pedal position sensor
The mechanic will replace the throttle body on your car if:
- It can’t be cleaned properly.
- The throttle flap, throttle shaft, or the mechanical linkages to the throttle cable are damaged.
- The electronic throttle actuator is faulty.
- There is a damaged throttle body or TP sensor electrical connector.
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
- A faulty throttle position sensor
- Gas pedal sensor problems
- Intake manifold pressure sensor issues
- A clogged air filter
- A bad Mass Airflow sensor (MAF sensor)
- A failing fuel pump
- A malfunctioning fuel injector
- A defective fuel pressure regulator
- These parts can cause problems similar to bad throttle body symptoms.
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers.
Throttle Body Replacement
1. Refer to the service manual for identification and location of the throttle body.
2. Remove the air intake duct from the throttle body once it is located.
3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement.
4. Pull out the cables from the throttle body.
5. Remove the hoses such as air or vacuum hoses from the throttle body.
6. Disconnect the throttle position sensor.
7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything.
9. Properly clean the assembly and port to remove any carbon build up.
10. Compare the old throttle body with the new one.
11. Install the throttle body in the port.
12. Fasten the bolts and screws to hold it in place.
13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body.
15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn?
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need?
Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required?
As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
- Disconnecting a battery cable
- A battery dies
- Replacing a battery
- Clearing the check engine light
- Replace an electronic throttle body
- Cleaning an electronic throttle body in an inappropriate way
- etc…
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn?
In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire).
If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn?
Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer.
| Item Specifics | |
|---|---|
| Bore Diameter | 60mm |
| Housing Length (in) | 5-7/8 |
| Main Port Inside Diameter (in) | 2-3/8 |
| Housing Width (in) | 4-15/16 |
| Air Intake Port Maximum Diameter (in) | 2-13/16 |
| Throttle Plate Diameter (in) | 2-3/8 |
| Mount Hole Quantity | 4 |
| Connector Quantity | 1 |
| Terminal QTY | 6 |
| Throttle Position Sensor Included | Yes |
| Fuel System Type | FI |
| Fitment Type | Direct Replacement |
| Items Included | One Complete Throttle Body w/Sensor |
| Packaging Type | Box |
| Brand | SCITOO |
| Manufacturer Part Number | SC16731501OO |
| Interchange Part Number | 67-0014,161193RC0A,16119ET000,161194AF0A,6E0014 |
| OE/OEM Part Number | 161199SE0A,16119ET00A,16119ET00B, |
| Superseded Part Number | 16119ET00C |
| Weight | 4 LB |
| Manufacturer Warranty | 1 Year |
| Placement on Vehicle | Front |
| Non-Domestic Product | Yes |
| Mounting Hardware Included | No |
| Modified Item | No |
| Custom Bundle | No |
| Type | Throttle Body |
| Features | Electronic |
| Connector Type | Plug |
| Fuel Type | Gasoline |
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order.
2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
3.Local pick up is not available.
4.International Buyers C Please Note:
a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.
b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ]
1.We accept multiple payment methods, such as VISA, Master Card, etc..
2.Please do not use the note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
4.Payment must be received within 7 days as auction ended or order might be delayed.
We stand behind every product we sell.
All of our brand new items come with a 30-Days money-back or exchange guarantee.
Q: How do I pay for my purchase?
A: MY store accepts VISA, Master Card, etc..
Q: When will the item be shipped out?
A: This item will be shipped with 2 business day once payment completed.
Q: Where is my tracking number?
A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email.
Q: How do I return an item?
A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ]
1. We will leave a feedback once we get your payment.
2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers.
3. If you are satisfied with the product you received, wish you can leave us a feedback.
Shop Category New List Item
Hot Item
Warranty
|
Throttle Body For Nissan Sentra Tiida Versa 1.8L NV200 Sentra 2.0L 16119ET000
Fits Applications For Nissan Cube 1.8L 2009-2014
Electronic Throttle Body the usual parts
The mechanic will replace the throttle body on your car if:
Additionally, it’d be a good idea to get your cars throttle and fuel delivery system inspected for:
How is Throttle Body Replacement Done?
You will need: screwdrivers, socket set, spanners, needle pointed pliers. Throttle Body Replacement 1. Refer to the service manual for identification and location of the throttle body. 2. Remove the air intake duct from the throttle body once it is located. 3. Check the throttle body as well as the assembly and ports. If there is wearing in the assembly it may also require replacement. 4. Pull out the cables from the throttle body. 5. Remove the hoses such as air or vacuum hoses from the throttle body.
6. Disconnect the throttle position sensor. 7. Remove the screws that are holding the throttle body in the assembly.
8. Remove the throttle body carefully after disconnecting everything. 9. Properly clean the assembly and port to remove any carbon build up. 10. Compare the old throttle body with the new one.
11. Install the throttle body in the port. 12. Fasten the bolts and screws to hold it in place. 13. Connect all the things that you previously removed.
14. After connecting everything start your engine and test for the new throttle body. 15. Perform the following check as a final test. Start the engine and take the car for a test drive. On your return, let the engine idle for about two minutes and listen for problems in the idle, ensuring that it is smooth. If it is not, then there may be additional problems throughout your engine.
Q: What is throttle body relearn? Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc. The symptoms are, idle is too low, too high, or erratic. Sometimes the engine stalls when you stop at the traffic light. And you may see the check engine light come on with the idle speed related trouble codes.
Q: Why does Idle Relearn need? Many newer vehicles use an electronic throttle body which contains a throttle plate, motor, and sensors. They are responsible for regulating all air flow into the engine, including the air flow for maintaining idle speed. When idling, the vehicles computer sends a signal to the throttle body and controls the throttle plate to adjust the idle speed depending on the engine temperature and whether AC is on or off. When the computer loses the connection to the throttle body, it loses the position of the throttle plate. Thus, the vehicle computer needs to relearn the throttle plate after losing connection to it.
Q: When is Idle Relearn required? As mentioned above, Idle Relearn is required when the vehicle computer loses the connection to a throttle body. And, many things cause it to happen.
Note: Please note that it doesn’t mean that you will need the idle relearn after these repairs or incidents. It totally depends on models of vehicles.
Q: Does my car need Idle Relearn? In general, the procedure of idle relearn is necessary on vehicles with electronic throttle body (=ETB aka DBW Drive-By-Wire). If you are experiencing a rough idle on your vehicle after you disconnect a battery for any reasons, you need to perform the idle relearn procedure.
Q: How can you get the procedure of idle relearn? Unfortunately, not all repair manuals have the information about idle relearn. And you may or may not find it in the owner’s manuals. So where can you find it? Go online, search “idle relearn + make, model, and year of your vehicle,” and you may get results. If not, search “idle relearn + make” only. The procedure may be the same among all vehicles from the same manufacturer. Shipping
1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. Payment
1.We accept multiple payment methods, such as VISA, Master Card, etc.. 2.Please do not use the note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 7 days as auction ended or order might be delayed. Returns
We stand behind every product we sell. Customer Services
Q: How do I pay for my purchase? Feedback
1. We will leave a feedback once we get your payment. Copyright of SCITOO-AutoParts . All rights reserved. |
