FAQ

배대지주소

사이즈조견표
주문/배송조회
입금액충전
입출금내역조회
마일리지조회
입금액환불요청
사업자정보등록
1:1문답
자주하는질문과답 FAQ
국제운송료 요율표
해외물류센터주소
사이즈조견표
취소/반품/교환/환불
파손/분실보상
통관/관세
에스크로서비스
개인정보취급방침
이용약관
회사소개
공지사항
찾아오시는길
아마존배송대행신청방법
사진확대

DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation
ASIN번호 B06XGD5SCB
상품상태 New   
상품구분 Tools & Home Improvement / Electrical
브랜드 DROK
판매자 미정
판매자위치 미확인
Size
현지 판매 가격
$16.99
상품가격 상세보기
관련상품



상품특징
Make sure this fits by entering your model number.DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W.STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time.FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation.PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ.UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module.
상품설명
Size:Dual H Bridge Motor Controller 7A Parameters: 1. Power supply voltage 6.5V-27V, the power cannot be reversed or over 27V, or may burn the module, it is recommended connecting in series 15A fuse in the power input. 2. Dual motor interface, each rated output current 7A, peak current 50A, the motor interface cannot short-circuit, it is recommended connecting in series 15A fuse. 3. The enable signal and forward and reverse control signal control voltage 3-6.5V. 4. Enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ, PWM minimum pulse width 10us. 5. Product dimension: 55x55x16mm  6. Installation hole diameter: 3mm, noted to prevent short circuit when install the reverse side, you can add insulation pad or copper column to raise the circuit board Parameters matched: Motors with rated voltage 24V, identification of rated power 115W or below, and motors with identification of rated current 7A can full work for a long time. Note:  1. Drive power cannot be reversed, it is recommended connecting in series 15A fuse in the power interface, the voltage should be between 6.5 - 27V. If over voltage, it may burn the drive module if power on. 2. It is recommended that the rated output current of the power supply be more than 2 times, in case the power supply voltage cannot reach the required input voltage of the motor when it is started, which   may cause pause of the drive module for under voltage protection. 3. Motor interface cannot be short-circuit, or may burn the drive module, it is recommended connecting in series 10A fuse in the motor interface. Package Including: 1x DC Motor Driver Board
































상품특징
Make sure this fits by entering your model number.DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W.STRONG DRIVE: the motor controller board adopts dual H bridge, can drive two DC motors at the same time.FORWARD and REVSERSELY ROTATE: the IN1, IN2/IN3, IN4 port can control forward or reverse motor rotation.PWM SPEED CONTROL: enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ.UNDER VOLTAGE PROTECTION: the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module.
상품설명
Size:Dual H Bridge Motor Controller 7A Parameters: 1. Power supply voltage 6.5V-27V, the power cannot be reversed or over 27V, or may burn the module, it is recommended connecting in series 15A fuse in the power input. 2. Dual motor interface, each rated output current 7A, peak current 50A, the motor interface cannot short-circuit, it is recommended connecting in series 15A fuse. 3. The enable signal and forward and reverse control signal control voltage 3-6.5V. 4. Enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ, PWM minimum pulse width 10us. 5. Product dimension: 55x55x16mm  6. Installation hole diameter: 3mm, noted to prevent short circuit when install the reverse side, you can add insulation pad or copper column to raise the circuit board Parameters matched: Motors with rated voltage 24V, identification of rated power 115W or below, and motors with identification of rated current 7A can full work for a long time. Note:  1. Drive power cannot be reversed, it is recommended connecting in series 15A fuse in the power interface, the voltage should be between 6.5 - 27V. If over voltage, it may burn the drive module if power on. 2. It is recommended that the rated output current of the power supply be more than 2 times, in case the power supply voltage cannot reach the required input voltage of the motor when it is started, which   may cause pause of the drive module for under voltage protection. 3. Motor interface cannot be short-circuit, or may burn the drive module, it is recommended connecting in series 10A fuse in the motor interface. Package Including: 1x DC Motor Driver Board




























2019-04-07 04:13:59